VBBIBRBwwVcB ++VBEFigure 1IcRc+VCEIE+Vcc (a) For the BJT configuration in the Figure 1, the following values is given: Vcc=25V;VBB = 2.5V; RB = 4.7 ks; Ic (sat) = 18 mA, VCE (sat) = 0.5 mV and BDc = 80.i)Calculate the value of IB and Rc.ii)Determine whether the transistor of BJT configuration is saturated or not andjustify your answer.What will be happened to the transistor if the IB is changed to 0.25 times fromorigin values?iii)

The required parameters can be calculated by using the DC analysis of the given amplifier circuit.

(a) For the BJT VBB = 2.5V; RB = 4.7 kS; Ic (sat) = 18 mA, VCE (sat) = 0.5 mV and BDc = 80. i) Calculate the value of IB and Rc. ii) configuration in the Figure 1, the following values is given: Vcc=25V; 111) Determine whether the transistor of BJT configuration is saturated or not and justify your answer. What will be happened to the transistor if the IB is changed to 0.25 times from origin values?

(a) For the BJT VBB = 2.5V; RB = 4.7 kS; Ic (sat) = 18 mA, VCE (sat) = 0.5 mV and BDc = 80. i) Calculate the value of IB and Rc. ii) configuration in the Figure 1, the following values is given: Vcc=25V; 111) Determine whether the transistor of BJT configuration is saturated or not and justify your answer. What will be happened to the transistor if the IB is changed to 0.25 times from origin values?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter30: Dc Motors

Section: Chapter Questions

Problem 6RQ: What is CEMF?

See similar textbooks

Similar questions

FAIRCHILD Discrete POWER & Signal Technologies SEMICONDUCTOR ru 1N4001 - 1N4007 Features • Low torward voltage drop. 10 a14 * High aurge eurrent cepablity. 0.160 4.06) DO 41 COLOR BAND DGNOTEs CAT-Cos 1.0 Ampere General Purpose Rectifiers Absolute Maximum Ratings T-26*Cuness atnerwioe rated Symbol Parameter Value Units Average Recttied Current 1.0 375" lead length a TA - 75°C Tsargei Peak Forward Surge Current 8.3 ms single halr-sine-wave Superimposed on rated load JEDEC method) 30 A Pa Total Device Dissipetion 2.5 20 Derste above 25°C Ra Tag Thermal Resistence, Junction to Amblent 5D Storage Temperature Range 55 to +175 -55 to +150 Operating Junetion Temperature PC "These rarings are imithg valuee above whien the serviceatity or any semiconductor device may te impaired. Electrical Characteristics T-20'Cunieas ofherwise roted Parameter Device Units 4001 4002 4003 4004 4005 4006 4007 Peak Repetitive Reverse Vellage Maximum RME votage DC Reverse Voltage Maximum Reverse Current @ rated VR…
GIVE DETAIL EXPLAIN PLEASE! with cicruit drawing.. Ans : Rth = 28 ohm Vth = 92 V.
Hi! Please help me answer this problem our topic here is about Diode in DC & AC Circuits. Please show your correct and complete solution. ASAP! THANK YOUUU!
What are IC Voltage regulators? State the different IC voltage regulators and its operation.
For the circuit in the figurea) Determine the time constant.b) Write the mathematical expression for IL, VL and VR, after the switch is closed.c) Determine IL, VL for one, three and five time constants.d) Draw the waveforms of IL, VL and VR.
A resistor Ra is in series with a voltage source Va. Draw the circuit. Label the voltage across the combination as v and the current as i. Draw and label the volt–ampere characteristic (i versus v).
quations. 3. What are the advantages and disadvantages of a dual slope ADC? a blecL mation
8. Determine the output voltage V, and the Zener diode current Iz for the circuit below. The Zener diode is IN5236B. }} a) E-21 V, R1=1 km2, and R2-2 km2 b) E-21 V, R1-2 k2, and R2-1 k E R₁ www R₂
Vps = 10 V R = 0.1k02 ww -ovo R₁. Consider the Zener diode circuit shown in figure. The Zener diode voltage is Vz= 5.8V at Iz= 10mA and the Zener resistance is rz = 200. a) Find the output voltage for RL = 1k0 b) Find the change in the output voltage when the load resistance varies +ARL.
(02) DC Si Diode Circuit. (Course: Electronic Devices and Circuit Theory) What is the minimum value for RL needed to turn Zener diode ON?, And what is the maximum value for RL needed to turn Zener diode is ON? -Use Equation Operators or write it down on paper/digital paper. -Redraw and Apply. -You can add //comments for a better understanding. -Please answer without abbreviation. -Make it clean and clear typing/writing. Thank you.
A Capacitor filter is used at the output across the load in order to minimize the ripple factor of the output voltage. The expressions of the average output voltage Vpc and the output AC component VAc are given below. If R = 1k2 and the single phase bridge rectifier supplied from a 120V - 50 Hz sinusoidal source, then the capacitor value that will maintain the amount of the output ripples to less than 4% would be equal to: VDC = Vm(4FRC – 1)/4ƒRC) VAC = Vm/(4/2ƒRC) Select one: O a. 63.39uF O b. 33.2uF O c. 93.39UF O d. 126.2uF TOSHIBA
Q 2) A single phase half-wave uncontrolled rectifier with RL load is shown With R=1002, La 0. 1H w-377rad/s and V 100V, Determine: a) An expression for the load current i(t). b) The value of the current at t3D16 ms. c) The average load current (1C WLialx197=ア7.9 =121 V, = V, sinfar) 17.2 0.360