T(s) Mechanical (s)SubsystemV,(s)Electrical|(s)e(s)TorqueCoupling1/sSubsystemVa(s)Back emfCouplingFigure 2: Sub-systems that can be identified in the electric motor. (a) For each of these blocks now write down the transfer that will describe the input-output characteristics of that block.Va(s)I(s)T(s)e(s)Vo(s)

Answered: Image /qna-images/answer/238b164f-30c3-401e-ba43-73dc26bfb8af.jpg

Answered: (a) For each of these blocks now write…

(a) For each of these blocks now write down the transfer that will describe the input- output characteristics of that block. Va(s) I(s) T(s) (s) e(s) Vo(s)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

BW of an analog signal is 150 Hz. The sampling rate of ADC which :converts that signal to discrete form is between 100 and 200 sample/s 100 sample/s O Less than 100 sample/s O 200 sample/s exactly. O 300 sample/s or higher O
A 3-bit binary weighted resistor DAC and a 3-bit R-2R ladder DAC have common values of Vref = 5V, R = 1kN, R = 2kN. Compare their output voltages for each of the following binary inputs. What do you observed? Binary Weighted Resistor DAC Resolution Binary input R-2R Ladder DAC Output voltage Resolution Output voltage 000 001 010 011 100 101 110 111
2) Dead space is defined as the range of different input values over which there is no change in output value. Select one: True False
Question 8 160 Which of the po160100555- 870479447 In the DAC unit, the analog level at the A 1601005559870479447 g160100555 B 0870479447 There may be applications that require digital-to-analog conversion but do not need analog-to-digital conversion. 9870479447 1601008 9441 Basically, the process is the reverse of the conversion) changed and in this 160 0555 - 987 9441 The signal produced by this conversion process can basically be 555-987 s respect it is similar то 916 It would not be possible to produce a realistic sine signal with a 4-bit DAC unit. 087047944 to the PWM unit. 1601008 160100555 measured with a DC multimeter. 2555-987047944 g160100555 - 7944 9168
H.W: For a five-bit resistive divider, determine: a) The weight assigned to the LSB, also the second, and the third LSB. B) The change in output voltage due to a change in the LSB. C) The output voltage for a digital input of 10110. Assume 0-0V and 1= +10V.
Q44) In the STM diagram fragment below, we see five transitions marked with italic letters. Which option cannot have a guard condition added? dev2/x=x+1 A. a B. b C. c D. d E. e b a/beh Ev1/beh с e
Sample-and-hold circuits in analog-to digital converters (ADCS) are designed to stabilize the input analog signal during the conversion process stabilize the comparator's threshold voltage during the conversion process. sample and hold the D/A converter staircase waveform during the conversion process O sample and hold the output of the binary counter during the conversion process.
Q6) Analyze the counter shown in figure below. The most significant bit is C. The row represent the present state and the column represent the next state. Analyze the counter shown in figure below. The most significant bit is C. The row represent the present state and the column represent the next state. * FF-B FF-A 000 001 010 011 000 001 010 011 100 101 110 111 ם
Scimal value of the value that will occur at the ADC output. (ADC is 12 Question 2 MN is the last two g160100555 - yu digits of In an analog measurement operation set as an external reference, the reference source of the ADC is a voltage source of 5 analog input, write the g160100555-Gu Aumber your student 010055 g160100555 - Yu 9441 20100 g160100555- Y 44 s0100538 g160100555 - Y 944 201005 g160100 2447 .5Volts. In case of 3.5V voltage to the 30100555 -98 9447 30100555 - 987 30100555
Compute the complete (input & output) characteristics of n-channel JFET in the form of curves.The JFET has typical parameters as IDSS=12mA and VGS(off)= -5V.
a) Fill in the table below for 4-bit A/D converter if Va = 13V with a reference voltage of 15V. Show your work. Analog " Table - Successive approximation process for Va = 13V Vb B3 B₁ Step 1 B₂ 0 8V 1 0 Bo 0 Clock Comparisons Is Va ≥ 8V F Sample-and-hold 4- SAR 4- DAC 4-bit register Logic control Ring counter Answer Yes gffffe MSB LSB Output
. An 8-bit A/D converter has an input range of +/-8V. If the input is 7.5V, what is the quantization error (in +/-V)? - An 8-bit A/D converter has an input range of +/-8V. If the input is 7.5V, what is the quantization error as a +/-% of input voltage?