A) Figure (2) shows the velocity distribution for flow of water between two parallel plates. Velocity profile: u = 10(0.01y - y²). Find: 1) The value of Y. 2) Shear stress at the wall. 3) Shear stress at 20μm from the wall. 4) Location of zero shear stress 5) Location of maximum velocity. T= water at 2PC Figure (2)

Q: A) Figure (2) shows the velocity distribution for flow of water between two parallel plates.…

A: u=10 (0.01y-y2)1) Value of YCalculating values of y when velocity(u)=00.01y-y2=0y=0.01 m & 0…

Q: The velocity distribution for water (20?C) near a wall is given by u=a(y/b)1/6, where a=10 m/s, b=2…

A:

Q: 2 If the velocity distribution over a plate is given by u = y - y² in which u is the Problem…

A: Given: Velocity Distribution u=2y3-y2, Dynamic Viscosity μ=8.63 Poise=8.6310=0.863 Ns/m2, It is…

Q: H.W. Determine the horizontal force P required to cause slippage to occur. The friction coefficients…

A: Given:    To Find: Horizontal force P, required to cause slippage to occur.

Q: please solve the problem in the picture, final  answer is 233KN/m

A: Step 1: Determine maximum moment, M ( For simply supported Maximum moment is located at midspan so…

Q: Q2) A parallel plate is moving over another plate as shown in the figure below. The liquid viscosity…

A:

Q: water flows in a 2am dia. pipe, Calculate the largest discharge upto which flow will be definitely…

A:

Q: Consider the following steady, two-dimensional velocity field: V (u, v) = (0.41 +2.1lx)7 +…

A: GivenV→=(0.41+2.1x)i+(-3.3-2.1y)ju=0.41+2.1xv=-3.3-2.1y at Stagnation pointu=v=0so,

Q: The thin-walled single cell beam shown in figure has been idealized into a combination of direct…

A: To determine the location of the shear center for vertical shear loading, we can use the principle…

Q: 4. If the moment acting on the cross section of the beam is M = 4kip.ft, determine the maximum…

A:

Q: 14. A fluid of specific gravity 0.96 flows steadily in a long, vertical 2.5 cm diameter pipe with an…

A:

Q: Water flow over the fixed surface causing the viscous velocity (in m/s) variation along y direction…

A: Given; Velocity distribution (u)  = 2y-2y³+y⁴ Dynamic viscosity= 1cp

Q: Given: Figure Find: External reactions in x and y directions needed to hold fixed vane. Solution: -…

A:

Q: A beam shown on the figure is subjected to a uniform load of 5 kN/m. Determine the minimum shearing…

A:

Q: The wall shear stress Tw for a flow in a narrow annular gap between a fixed and a rotating cylinder…

A: Given:- The wall shear stress for a flow in a narrow annular gap between a fixed and a rotating…

Q: 2.57 The velocity distribution for water (20°C) near a wall is given by u = distance from the wall…

A:

Q: . A cantilever wide-flange beam is loaded by a force P at the free end acting through the centroid…

A: Given  Cantilever beam point load acting on its free end  Cross section of the beam is I.

Q: Problem 6 A water tank 3m in diameter and 6.5 m high is made from a steel having a thickness of…

A:

Q: Analyse the structure shown in Figure using consistent deformation methods, then draw the Shear…

A: Using method of consistent deformation,....drawing of SFD and BMD for BC

Q: Find the maximum compressive and tensile normal stresses in the section given in the figure. Draw…

A:

Q: What are the three different project models for carrying out construction work?

A: Three different types of project models for carrying out construction work are as follows :-  EPC…

Q: Plane Stress in the stress element piven in fipure, with mohr circle; a) Detesmine the principal…

A: Mohr's circle method The graphical representation of plane stresses forms a plot known as Mohr's…

Q: Using the momentum integral equation set out below as a starting point and the quadratic function…

A: Given Data:fx=2n-n2dfndn=2-2ndfndnn=0=2μUδdfndnn=0=ρV-2dδdx∫o1fn1-fndn

Q: Determine the wall shearing stress in a pipe of diameter 100mm, which conveys water. The velocities…

A: Diameter of pipe = 100mm Velocity at bottom = umax = 2m/s Velocity at 20mm from the wall of pipe = u…

Q: 2. The cross section of an idealised thin wall symmetrical wing box beam is shown in Figure Q2. The…

A: Given data: Point load=1 kN e=250 mm E=70 GPa G=25 GPa   It is asked to calculate: 1. Shear flow…

Q: The section of a gate at the end of a tank is shown below. The length of the gate is 3 m  normal to…

A:

Q: T b = 3 ft., L=5 ft., T=500 ft-lb CCW, P = 500 lb Dia. = 10 in., Area = 78.54 in^2, Ix=ly=491 in^4,…

A: Step 1

Q: Air Question 5. 1,2 m wide AB gate is articulated from point A shown in the figure. The heights of…

A: The given figure is shown below:

Q: Analyse the structure shown in Figure using consistent deformation methods, then draw the Shear…

A:

Q: Q.17 For a liquid velocity u varies with y as follows U = 3y - 6y² 2 U = m/s and y is in meter for Y…

A: Given data- Velocity variation- U=3y-6y2, Viscosity- μ=1 poise, To Find- The shear stress in the…

Q: Determine the shear stress in point D in beam shown in Figure 5. 150 kN 2 m 20 kN/m b 75 mm D. h A B…

A: Solution:-

Q: Consider the retaming wall shown m the ligure helow Calculate the Rank me passive force per unit…

A: Passive pressure is a condition in which the retaining system exerts a force on the soil. Since…

Q: Q2 The T section is shown in Figure below is the cross-section of a beam. The beam is subjected to a…

A:

Q: kN is distributed equally among the three rivets. Determine the tensile stress (MPa) in the plate at…

A: P=70kN Width B=130mm Thickness t=25mm Diameter d=20mm

Q: Determine the shear stress at y=0

A: Given:  Velocity distribution, u=34y-2y2 Dynamic viscosity = 8.63 poise To find: Shear stress at y=0…

Q: a. By equation Method, Draw shear force and bending moment diagrams. b. Draw bending stress…

A:

Q: Q.5 The velocity distribution for flow over a plate is given by U=2y-y² in which u is the velocity…

A: given- velocity distribution-u=2y-y2distance=0.2 mdynamic viscosity=0.9 Ns/m2

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?