A fence has a dimension of 15 meters long and 20 meters high including the portion below NGL. How many bags of cement will be needed for the cement mortar using Class A mix. CHB used is 200x200x400mm Choices A)587 B)438 C)383 D)299

A fence has a dimension of 15 meters long and 20 meters high including the portion below NGL. How many bags of cement will be needed for the cement mortar using Class A mix. CHB used is 200x200x400mm Choices A)587 B)438 C)383 D)299

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: To test the compressive strength of cement mortar, three 2” cubes were cast with three different…

A: Given: Length of mortar cubes = 2 in Mix No. w/c Ratio Cube No. Maximum Load (lb) 1…

Q: Calculate the volumes of the hydration products for 150 gm of cement with 0.5 w/c ratio, assume…

A: It is required to determine the volume of dry cement actually hydrated. Vcah=Weight of dry cement…

Q: Create a design mix using the ACI DESIGN MIX PROCEDURE with the following parameters: Non-air…

A: Design of concrete mix for 35 MPa Assuming 5 percent of results are allowed to fall below specified…

Q: TABLE P6.22 Cubes Made with Nonpotable Water Cubes Made with Potable Water 14,530 16,530 15,820…

A: Given Values are Nonpotable Water and Potable Water. First calculate the average values as below.

Q: Water cement ratio is a) Volume of water to the volume of cement b) Volume of water to the volume of…

A: Water cement ratio is defined as the ratio of Volume of water to the volume of cement . Water cement…

Q: Briefly describe the soundness of cement?

A: Soundness of cement : Soundness of cement can be defined as its ability to retain its volume after…

Q: In the normal consistency of paste cement, If I get 30 percent normal consistency, what does it…

A: In the normal consistency of paste cement, If I get 30 percent normal consistency, Implies as :…

Q: A trial concrete mix is to be prepared for a garage floor which is subjected to freezing. and…

Q: Q a) What particular precautions would you take when concreting (i) In winter, and (ii) in hot…

A: Brief concept- Concreting- It is the process of putting the concrete in the work location and…

Q: 1. (a) The data presented below is compiled to obtain the modulus of rupture values of the MgO…

Q: Explain cement manufacturing process and mention major differences between dry process and wet…

A: Cement production is indeed a complicated procedure that starts with mining but instead of grinding…

Q: Estimate the slurry volume used to cement the 600 feet cement Colum in the casing schematic ow. How…

A: As mentioned in the question, Take bottom 600 ft as column height.

Q: What are the methods to reduce total heat of hydration of cement?

A: Application of water to concrete mix starts a reaction between water and 4 bogues compounds present…

Q: When it comes to Type III cement, why isn't pozzolan used?

A: Type III Portland cement is rich in Calcium trisilicate (C3S), this constituent is most responsible…

Q: what is the aci design mix or proportioning of standard compressive ddesign strength values (without…

A: The American Concrete Institute (ACI) mix design method is but one of many basic concrete mix design…

Q: QUESTION 5 An S18x70 steel section is available with nominal depth of 9 inches O True False QUESTION…

A: 5. From the Standard Steel Beam Sizes, Dimensions, and Section Properties Chart, An S18×70 steel…

Q: Compare the setting time of a Portland cement and pozzolan cement? Provide a thorough discussion.…

A: When compared the setting time of Portland cement and pozzolan cement, the initial setting time of…

Q: Why is super plasticizer added to concrete? 1. To reduce the quantity of mixing water. 2. To…

A: Superplasticizer added to concrete because : Reduce water cement ratio Reduce quantity of cement…

Q: d. Using water reducer, how can we reduce cost without changing workability or strength? (Assume…

A: Given:- The result of an experiment shows the effect of the water reducer To determine:- d) How to…

Q: For the following concrete mix design 1:0.51:1.29:3.6 (P:W:S:G), how much of each individual…

A: We will solve this question in step no. 2

Q: Q4. Use the information in column B to fill in the missing parts of the sentences in column A: A B…

A: Rapid hardening Portland cement has more C3S and less C2S.

Q: 6.38 What is the source of fly ash? Why is fly ash sometimes added to concrete? What are the…

A: Given : fly ash To determine : 1)source of fly ash 2)Why added in concrete 3)Different class of…

Q: List rarely used concrete additives and give specific areas to be used. (Other than water reducers,…

A: Few rarely used chemical admixtures are listed below and usage is also given : 1) Air entraining…

Q: From the knowledge of the effects of GGBS, PFA and microsilica, indicate whether their inclusion to…

A: Required to find: How the presence of GGBS, PFA and microsilica effect the a) Alkali silica…

Q: Three standard mortar cubes were made using nonpotable water available at the job site, and three…

A: ASTM standards : - Average Compressive strength of Non - potable water should be greater than 90 %…

Q: Write any differences between plain and reinforced concrete column

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Three standard mortar cubes were made using nonpotable water available at the job site, and three…

A: Standard Requirements of ASTM for adding water in concrete are as follow ; - Average compressive…

Q: In order to evaluate the suitability of nonpotable water available at the job site for mixing…

A: Given values: Compressive strength of mortar cubes after 7 days of curing tested and failure loads…

Q: Questión 2 Refer to Appendix A for tables and equations to be used. Use the CNCI method. You are…

A: As per the given information we have calculate the following things which are: amount of water…

Q: According to astm how much content of lime shall be added to Portland cement and how it is…

A: The Portland cement: Portland Cements, by definition, are hydraulic cements; that is, they set and…

Q: Subject concrete technology Q: a)What particular precautions would you take when concreting (i) In…

A: Thank you for the question . As per honour code we are allowed to answer the first question since…

Q: A fence has a dimension of 15 meters long and 20 meters high including the portion below NGL. how…

A: From Table : Quantity of cement and sand CHB mortar per square meter For Size : (200 × 200 × 400) mm…

Q: Students in the materials class prepared three mortar míxes with water to cement ratios of 0.50,…

A: Given data: 50 mm cube.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Given the four concrete mixes as shown in the table below, one without water reducers and three (c1-c3) with water reducer. The most economic mix where the workability and compressive strength maintained as for the original mix (the mix without water reducers) is With water Reducer Without water Reducer C1 C2 C3 Cement, Kg/m3 850 765 850 850 Water, Kg/m3 465 419 370 465 Slump, mm 50 S1 50 S2 Compressive Strength (MPa) 38 fc1 fc2 fc3 Select one: O A. C3 О В. С2 О С.С1 O D. C1 and C2
An ASTM indicator of workability when evaluating freshly mixed Portland cement concrete. Choices: - C143 - C187 - C191 - C496
Which of the options are correct for a 3m³ of concrete having design mix proportion of 1:2:7 (by volume) A Volume of cement required = 0.318 m³ B No. of cement bags required = 15 C D Volume of coarse aggregate = 2.5 m³ Volume of water required = 1m³
Please give me both A and B right answers with clear explanation
Q # 4. Temperature of Mass Concrete can be controlled by using various techniques. Please suggest numerous ways to control the temperature of mass concrete by using ‘Mix Design Technique
Compute the Fineness Modulus for fine aggregate.
What is the purpose of adding gypsum while manufacturing cement; what are the consequences of making cement without gypsum?
10
Where MM is 25 and DD is 12.
Using given data and formulas, calculate evaporable moisture, surface moisture and absorption
Select the correct statement from the following Select one: O A. Admixtures increase the cost of the concrete mixes significantly. O B. Additives are functional additions blended in limited amounts into a hydraulic cement during manufacture C. Admixtures are usually added before mixing OD. Additives can be used to overcome certain emergencies during concreting operations.