A falling-head permeameter contains a sample of length 10 centimeters and diameter4 centimeters. The falling-head tube has an inside diameter of 1 centimeter. Thehead falls from 5 to 2 centimeters over a period of 70 minutes.What is the hydraulic conductivity in cm/sec?b. The water temperature was 21° C. At this temperature the density of water is0.997 g/cm' and the viscosity is 0.00988 g/sec-cm. What is the intrinsic permea-bility of the sample?а.

Answered: Image /qna-images/answer/a0818e2b-b33f-4cb4-b804-be0e266b273a.jpg

A falling-head permeameter contains a sample of length 10 centimeters and diameter 4 centimeters. The falling-head tube has an inside diameter of 1 centimeter. The nead falls from 5 to 2 centimeters over a period of 70 minutes. a. What is the hydraulic conductivity in cm/sec? . The water temperature was 21° C. At this temperature the density of water is 0.997 g/cm³ and the viscosity is 0.00988 g/sec-cm. What is the intrinsic permea- bility of the sample?

A falling-head permeameter contains a sample of length 10 centimeters and diameter 4 centimeters. The falling-head tube has an inside diameter of 1 centimeter. The nead falls from 5 to 2 centimeters over a period of 70 minutes. a. What is the hydraulic conductivity in cm/sec? . The water temperature was 21° C. At this temperature the density of water is 0.997 g/cm³ and the viscosity is 0.00988 g/sec-cm. What is the intrinsic permea- bility of the sample?

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter6: Hydraulic Conductivity

Section: Chapter Questions

Problem 6.14P

See similar textbooks

Similar questions

Refer to the constant-head arrangement shown in the figure. L Graduated flask Porous stone Soil specimen For a test, the following are given: •L=18 in. • A = Area of the specimen = 3.5 in.2 • Constant-head difference = h = 28 in. • Water collected in 3 min =21.58 in.3
Refer to the constant-head arrangement shown in Fig 5. For a test, the followingare given:• L =18 in.• A = area of the specimen = 3.5 in.2• Constant-head difference = h = 28 in.• Water collected in 3 min = 21.58 in3Calculate the hydraulic conductivity (in./sec).
A sample of sand, 5 cm in diameter and 15 cm long, was prepared at a porosity of 60% in a constant-head apparatus. The total head was kept constant at 30 cm and the amount of water collected in 5 seconds was 40 cm^3. The test temperature was 20 deg C. Calculate the hydraulic conductivity. a. 6.7 x 10^-1 b. 3.47 x 10^-2 c. 5.0 x 10^-2 d. 2.0 x 10^-1
In a falling head permeameter test the initial head at t = 0 is 40 cm. The head drops by 5 cm in 10 minutes. Determine the time required to run the test for the final head to be at 20 cm. Given: Height of sample = 6 cm; cross sectional areas of sample = 50 cm2 and stand pipe = 0.5 cm2. Determine the hydraulic conductivity in cm/sec.
For a falling head permeability test, the following values are given: Length of specimen: 200 mm Area of specimen:1000 sq. mm Area of standpipe: 40 sq. mm Head difference at t= 0: 500 mm Head difference at t= 180 sec : 300 mm Determine the hydraulic conductivity (cm/sec)
A constant head test is performed using a permeameter in the laboratory. The graduated cylinder collects 892 cm3 of water in 112 seconds. The soil specimen diameter = 18 cm , th elevation of water in upper-most piezometer is 181 com , the elevation of water in lowest piezometer is 116.6 cm and the piezometer inlets are evenly spaced at 16.7 cm on center. Compute the hydraulic conductivity, k and choose the correct answer below based on that. O A. 2.1 x 10^-3 cm/second O B. 1.5 x 10^-2 cm/second O C. 2.91 x 10^-2 cm/second O D. 2 x 10^-2 cm/second QUESTION 10 Given: -Applied stress on a soil = 122 kPa %3D -Influence Factor = 0.4 Compute the change in stress at 10 m below the edge of 25 m dimeter oil tank and select the correct answer from below: O A. Change in stress = 44 kPa O B. Change in stress = 49 kPa O C. Change in stress = 40 kPa O D. Change in stress = 42 kPa %3D
In a constant-head permeability test. A test gives these values: •L= 25 cm •A = 160 area of the specimen cm2 • Constant-head difference, h =1m • Water collected in a period of 5min and 40sec= 1 Liters Calculate the hydraulic conductivity in cm/sec.
1. A 30cm long field sample is tested in a falling head permeameter with a 10 cm diameter cylinder. the diameter of the tube is 10mm. the water level in the tube is 35cm above the outlet level after one hour of operation, while the level drops to 22cm after 12 hours of operation. find the hydraulic conductivity of the sample.
In a smooth pipe of uniform diameter 30 cm a pressure of 60 kPa was observed at section 1 which was at elevation 13.00 m. At another section 2 at elevation 15.00 m the pressure was 30 kPa and the velocity was 1.5 m/s. The fluid in pipe is water. The head loss between two sections is m.
Estimate the ratio of equivalent hydraulic conductivity
The permeameter in a permeability test setup involves a sample 200mm diameter and a length of 30mm. The height of water is kept constant at 400mm. In a duration of 4 min, water was collected in the graduated flask having a volume of 450cu.m. Determine the Hydraulic Conductivity.
In using a permeameter, it is sometimes convenient to make a “falling -head” test. The horizontal tube is 1 m long and 10 cm in diameter and is filled with sample material. During a test, the upstream head h₁ falls from 200 to 180 cm in 4 hr, while h₂ is held constant at 15 cm. The diameter of the vertical tube in which h₁ is measured is 40 cm. What is the indicated average hydraulic conductivity? Estimate the range between maximum and minimum values of hydraulic conductivity.