A diffuser is integrated into a system. Superheated water vapor enters the diffuser at a temperature of 473.15K and a pressure of 10 bars. The incoming velocity of the vapor is 100 m/s and exits at 30 m/s. The inlet diameter of the diffuser is 40 cm. At the exit of the diffuser, the pressure of the saturated vapor is 3 bars. The exit area (in square meters) of the diffuser is: O 3.333 O 1.232 O 0.102 O Cannot be determined with the information provided

A diffuser is integrated into a system. Superheated water vapor enters the diffuser at a temperature of 473.15K and a pressure of 10 bars. The incoming velocity of the vapor is 100 m/s and exits at 30 m/s. The inlet diameter of the diffuser is 40 cm. At the exit of the diffuser, the pressure of the saturated vapor is 3 bars. The exit area (in square meters) of the diffuser is: O 3.333 O 1.232 O 0.102 O Cannot be determined with the information provided

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. Determine the horizontal and vertical stroke af a slider D and F when crank AB rotates 30 degrens sideways. AB-20, BC-25, CD-30, 8D-50, CF-45cm. Draw in appropriate scale E A B G
In a spur gear arrangement, the driver has 80 teeth of 39 mm pitch. Find the power, if it can transmit a tangential force of 60 N. Take speed of driver as 150 rev/min. Insert your answer for power in watt correct up to at least a third decimal place.
The diagram below shows a shaft with spur gear (B), bevel gear(D), and two supporting bearings (A and C). All dimensions are in millimeters and all shoulder fillets (at points where diameter changes) have a radius of . The pressure angle for the spur gear at B is . The pressure angle for the bevel gear at D is and the bevel angle is . Note that the shaft is designed so that only bearing A takes thrust. The shaft is made of steel with . All the critical surfaces are ground. The shaft rotates at . A motor with a power of is connected at the bevel gear through another bevel gear. This drives the shaft. A load is connected through another spur gear at the output spur gear at B. The standard deviation on the power is . (a) Determine the forces acting on the gears. Recall that for a spur gear, the relation between the tangential component of the force and the radial component of the force and the pressure angle is given by . For this bevel gear, the axial (thrust) component of the force on…
I need answer within 20 minutes please please with my best wishes
Find the greatest and smallest values of the velocity ratio of two shafts joined with a universal coupling when the axes are at 60o to each other. Produce a graph of velocity ratio against angle for f to proof the calculated results.
A spur gear has a pitch diameter 3. Calculate its clearance.
Two parallel shafts are to be connected by spur gearing. The approximate distance between the shafts is 600 mm. If one shaft runs at 120 r.p.m. and the other at 360 r.p.m., find the number of teeth on each wheel, if the module is 8 mm. Also determine the exact distance apart of the shafts.
In a spur gear arrangement, the driver has 70 teeth of 26 mm pitch. Find the power, if it can transmit a tangential force of 100 N. Take speed of driver as 160 rev/min. Insert your answer for power in watt correct up to at least a third decimal place.
The maximum sliding velocity of the teeth of two gear wheels in mesh is 0.32 m/s. The wheels are of module 5 mm and have 32 and 44 teeth respectively. The addendum for each wheel is 1.2 times the module and the pressure angle is 20°. Calculate: 2.1. The number of teeth in contact. 2.2. The angular speed of each wheel.
Two shafts, each carrying a four-stepped pulley, are to be connected by a crossed belt. The driving shaft is to turn 150 rpm while the driven shafts is to turn 50, 150, 250 and 600 rpm. The smallest step of the driver is 10 in. in diameter. Find the diameters of all steps. Please Show a clear and detailed solution (with illustration). Thank you!