A differential manometer connects two pipelines as shown. Fluid 1 is water and fluid 2 is glycerin (SG = 1.26). Temperature is 20°C. hi = 27 cm h2 = 28 cm h = 33 cm Determine the difference in pressure between the two pipes. Which pipe has the higher pressure? Fluid 1

A differential manometer connects two pipelines as shown. Fluid 1 is water and fluid 2 is glycerin (SG = 1.26). Temperature is 20°C. hi = 27 cm h2 = 28 cm h = 33 cm Determine the difference in pressure between the two pipes. Which pipe has the higher pressure? Fluid 1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1(b) A multi fluid manometer is shown in Figure Q1(b). Determine the following: (i) Determine height 'h' if the difference in pressure between the two pipes is 15.38 kPa; (ii) Difference in pressure between the two pipelines if both pipes are in the same level. Take density of air = 1kg/m³ and density of water = 1000kg/m³. Oil SG 0.79 Gasoline SG = 0.70 PIPE Air- 45 cm Pipe hcm 22 cm 10 cm `Water `Mercury SG = 13.6
Correct and complete solution
Problem 4: A manometer attached to a rigid tank as shown, is used to measure the pressure, P, of the gas in the tank. Using the data in the figure, find the absolute pressure in the tank for the following two scenarios. The manometer fluid is mercury at 20 °C. a. b. The manometer fluid is water at 20 °C. Gas, P 19 cm 4 cm Patm 101 kPa
Three points 1 to 3 are identified in the figure. Which of the following statements is correct for their pressure? F1 P2 h Hydraulic oil SG = 0.870 P1 P3 O a. P1=P3 P2 O c. P1=P2 > P3 O d. P1=P2=P3
The U-Tube manometer is widely used to measure the difference in pressure between two containers or two points in a given flow system. As an example, a manometer connected between pipes A and B is shown determine the pressure difference in the two pipes. All dimensions shown are in centimeters. Kerosene Benzene Air PA 40 Pa 9 20 14 Mercury Water الانتقال إلى موقع الويب II اضف ملف ...
4. For the inclined manometer shown, determine the pressure difference between points "A" and "B", in kPa, for the fluids heights shown. * oil (sg = 0.80) glycerin (sg = 1.3) 90 mm B 80 mm 60 mm 30 mercury (sg = 13.6)
1. Atmospheric pressure is about 80 kPa (absolute). Water pressure at the base of a water tower is 600 kPa (gauge). Determine the following: Gauge pressure at the base of the tower Absolute pressure at the base of the tower A pipe carries water at a flow rate of 90 L/s. Determine the minimum inside diameter so that the average velocity of the fluid does not exceed: 3 m/s 2 m/s 4 m/s A 20 mm diameter copper pipe (19.94 mm inside diameter) carries water at a flow rate of 40 L/s. Determine the average velocity of the fluid.
Water is contained in both sides of the cylinder system shown below and the valve is closed. If the pressure on the right hand side of the valve is 119.6 kPa, what is the height in tank B, i.e. what is hp 1? Assume that the atmospheric pressure is 100 kPa, the acceleration due to gravity is 9.807 m/s² and the density of water is 1000 kg/m³. A Po B ha,1=1.5 m Water Water hg,1 1.0 m 0.5 m Pval,left Pyal,right A) 1.0 m B) 1.5 m C) 2.0 m D) 2.5 m
1. A U-tube manometer filled with Liquid A is attached to the underside of 4 inch pipe carrying water, as shown in Figure 2. At a point directly above the inclined U-tube manometer tap, the upstream tap of an inverted U tube is located. The inverted-U-tube manometer is filled with a Liquid B. If the P; = 17 psi, determine; (Note: I in (inch) = 25.4 mm, 1 atm = 101.325 kN/m² = 1.01325 bar = 101.325 kPa = 14.7 psi, g =9.81m/s³). (a) the differential manometer reading (psig), and (b) the value of X (inch). Liquid B, SG = 0.5 37 in. 12 in. Water P1. Pz. 4 in. X in. 58 in. 45° Liquid A, SG = 13.6