A diesel engine delivers 69 hp @ 2100 rpm to "Gear 1" of the compound gear train shown below. If there is a 13% power loss across the entire gear train, what torque is applied to the shaft connected to "Gear 4"?

Q: Compute the discharge velocity of air in ft/s if a turbo-compressor is used to compress 18 pounds…

A:

Q: A set of sprockets is constructed, as shown in Figure 1, so that the second and third rotate on a…

A: Solution: Given Data: r1=1 cmr2=4 cmrc=1 cmr3=3 cmN1=y rpmN2=u rpmN3=x rpm   To Find: (a) N1N2(b)…

Q: A metal bar at a temperature of 100 deg. F is placed in a room at a constant temperature of 0 deg.…

A:

Q: Fill in the blank which is given below Linear acceleration is equal to the product of and angular…

A:

Q: The velocity of the piston is 52.9901 3 ft/s.

A: use sine rule

Q: Problems 10-16 Information: Jose' pushes a wheelbarrow consisting of a wheel (mass mw = 3 kg, radius…

A: We can answer up to 3 sub-parts so we will answer  first 3 sub-parts for you. Please resubmit the…

Q: Completely solve and box the final answer. Write legibly 4. Compute the required size of the motor…

A:

Q: ven questions are subparts.. Kindly solve all a, b, c and d all answers otherwise leave it. Thank…

A: A) length of link AB=6002+3002                               =670.0 mmvelocity of point B=VB→ or…

Q: Solve with the correct unit 4. A cylindrical tank is 50 in. long, as a diameter of 16 in.and…

A:

Q: Find Ag and Ac AO2=30mm B AB=60mm AC=80mm BC=45mm B04=50mm 0,= 2 rad/s 0204=70mm 04 Note: angle…

A:

Q: . VELOCITY ANALYSIS. For the single-degree-of-freedom mechanism shown below, the angular velocity on…

A:

Q: A total of 10,000 BTU have been rejected from the condenser in two minutes. If the cooling capacity…

A: Given data Q=10000 BTU=1.055×107 JV=0.45 m3/minT2=120°F=322 K Here, Q is the heat transfer and V is…

Q: The piston displacement of an air compressor is 1200 liters per minute. Its bore and stroke are 12…

A:

Q: If the hydraulic cylinder at H draws rod BC in by a distance d = 4.545 in, how far does the slider…

A:

Q: Determine the mass of a steel ball whose diameter is 16mm.

A:

Q: Determine the following for point C on the slide if the angle theta measures 45 degrees and the BC…

A:

Q: Solve 0.782bar in p/q form

A: Given that : x = 0.782782782....... We need to find it in the form of p/q

Q: Find Ixx for the given Plane, where b1 =160m, d1=25m, b2=20m, d2=90m, b3=60m & d3=25 m (Enter only…

A: Given data:-b1=160m, d1=25m, b2=20m, d2=90m, b3=60m, d3=25mArea of section 1, A1=160×25=4000m2Area…

Q: Through load analysis, force and moment diagram are obtained, as shown below. Diagram below shows…

A: The force that occurs between mating gears is normal to the surfaces in contact. The axial force Fa,…

Q: Please show the computation in solving for NB and FAB

A:

Q: Draw the free-body diagram for the boom. Connection at A is a pin. Draw the vectors starting at the…

A: To draw: Free body diagram of the boom. Given: The connection at A is pin. Sketch: The force In wire…

Q: Find the limit. NOTE: Enter an exact limit if it erists. If the limit does not exist, indicate that…

A:

Q: For the quick-return mechanism shown below, the rod DC rotates with a constant angular velocity of 1…

A: For the solution refer below images.

Q: 9. There are 9.5 lbs of brass with specific heat of 0.095 BTU/lbm-ºR at a temperature of 295ºF being…

A: Given    Mass of brass, mb = 9.5 lbs      Specific heat, Cb = 0.095 BTU/lbm-ºR    Mass of water, mw…

Q: Cork k =.045 also all are 300 K values ... please resolve

A:

Q: Write a MATLAB program that finds the sum for-25 to 5. (Increment by 5). By using (while „loop)

A:

Q: The wind velocity on the upstream side of a wind turbine is 5.2 m/s. If the turbine extracts 31% of…

A:

Q: FOLLOW THESE STEPS FOR UPVOTE Given Required Diagram Solution Conclusion Do not round off while…

A: At sea levelThe diameter of ballon d=8 indensity of air ρ=0.07498 lb/ft3Pressure P=14.7 psiawhen…

Q: The result that I got after solving it was 463.0721, is that correct?

A: Given: d= 0.27in τ capacity=26.5 ksi = 26500 psi. Factor of safety =1.6 To find: The maximum T-force…

Q: Item 1 of 1 In the figure shown, Given: VA=1.2 m/s 0 = 40° Solve for: a) velocity of B (m/s) b)…

A:

Q: Find the summation of all positive numbers less than 50 which are divisible on 3 or 7. Taina D

A: 3 or 7 which is divisible less than 50. we can say that

Q: In a distribution system, Reservoir A supplies water to a branched system with Reservoir B and…

A: A reservoir is a man-made mechanism for storing water. The majority of reservoirs are created by…

Q: A2.1 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A:

Q: 1. When Tom is at x =1m, what is the tensile force in the wire in Newton? If the wire can hold only…

A:

Q: Q4 Draw Front, Top and side view of the drawing shown below. All dimensions in mm and scale 1:1.

A: Required Front view, Top view and side view are drawn using first angle method of projections.

Q: Answer with True or False of the following question: 5. For a fluid at rest, the shear stress is…

A: 5 . For a fluid at rest, the shear stress is zero. True.   When we apply shear stress on solid it…

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A: Step 1:a. Equation for the differential area aligned horizontally The differential area element dA…

Q: If 1 Pa is equal to 145 psi, what algebraic equation is needed to find out how many MPa there are in…

A: Given that,  1 Pa = 145 psi So, 1 psi = (1/145 ) Pa So, x psi = (x/145) Pa....... This is algebraic…

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.