Q1:a) Design the oscillator in Figure1 to start oscillation withRclosed-loop gain of 8.5, thensustain oscillation at a resonantR1o VoutfrequencyAssumingof3.4 kHz.the drain-sourceIN914resistance of JFET is 600 N.2N5458b) What will be the feedbackR2C2resistancesettingwhenR3R4C3oscillation is stable?1.0 kNFigure1

Answered: Image /qna-images/answer/fc2e76a9-58ad-4e86-989e-e707f692d998.jpg

a) Design the oscillator in Figure 1 to start oscillation with Ry closed-loop gain of 8.5, then R1 sustain oscillation at a resonant o Vout frequency of 3.4 kHz. Assuming the drain-source IN914 resistance of JFET is 600 N. 2N5458 b) What will be the feedback setting R2 C2 resistance when R3 1.0 kfN C3 oscillation is stable? Figure1

a) Design the oscillator in Figure 1 to start oscillation with Ry closed-loop gain of 8.5, then R1 sustain oscillation at a resonant o Vout frequency of 3.4 kHz. Assuming the drain-source IN914 resistance of JFET is 600 N. 2N5458 b) What will be the feedback setting R2 C2 resistance when R3 1.0 kfN C3 oscillation is stable? Figure1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Calculate the total offset voltage for the circuit shown below for op-amp specification values of input offset values, VIO=11.9 mV and IIO=62nA with RF=15 k ohm and Rin=3k ohm.
Electrical Engineering Determine the following (i) Frequency of Oscillation (ii) Feedback fraction For the oscillator to start, what is the minimum (ii) value of voltage gain? If the value of L is doubled, what is the frequency of (iv) oscillation? Sketch and label the output waveform across the load resistance RL. (v) Vcc +12 V RF CHOKE C. 0.1 uF 10 ka 0.1 F C. 0.01 F R 10 ka R2 5 ka RS C 1 KAS0.1 F 0.01 uF 21 uH
Hand Calculation: 1. For different configurations shown in Figure 1, perform approximate hand calculations assuming that the operational amplifier is ideal. In each case sketch the expected output waveform in Table I. Assume that the sine and triangular waves have amplitude of 1V, the square wave varies from 0 to 5V with 50% duty cycle, and frequency of all signals is set to 1kHz. 2. Redesign the integrator circuit so that when the input is sine wave with frequency 1kHz the output voltage will have same amplitude. Use C=0.1μF. 3. Redesign the differentiator circuit so that when the input is sine wave with frequency 1kHz the output voltage will have same amplitude. Use C=0.1μF.
slove 5 (Use a BJT op-amp) 1 You’ve been asked to build an alarm system using monstable multvibrator having an active time pf 100msec.. Explain the principle of operation and the type feedback of the op-amp. What is the advantage of this circuit? 2 You’ve been asked to build a low frequency square wave generator using a basic comparator having a frequency of 10kHz and 50% duty cycle. Explain the principle of operation and the type of feedback of the op-amp. What is the advantage of this circuit? 3 3 Build a Wein-Bridge oscillator using, C=1µF and +10V power supply to produce 10 kHz sinusoidal waveform. Generate your plots and compare output results. Highlight any discrepancies and discuss what happens if we want to increase the frequency to 100 kHz. 4 Build a high frequency Colpitts oscillator producing 10kHz Discuss its advantage over RC oscillators. How can you modify the circuit to include a crystal in you circuit. What is a typical application of such an oscillator? 5 Discuss the…
What will be the CMRR of an opamp if the value of the common mode gain is 100 and the value of the difference gain is 106?
d. For the feedback amplifier,. determine the base, emitter, and collector voltages of each transistor. 12 V 220 2 P-80 -160 1.8 MA
1- Design a 2nd order Butterworth active LPF with cutoff frequency f=900 Hz using R1=R2=12 kN.
Introducion to Electronic Analysis and Design - CE05 To have a good amplifier Select one: a. The input resistance should be high b. the output resistance should be high c. the voltage gain should be equal to zero d. the current gain should be equal to zero Ssment CE255/EE255 (O1)- Dr. Mamoun Al-Mistar Jump to...
What is the frequency of oscillation of the Astable Multivibrator circuit. Sketch the Vo and showcomplete details. Opamp is 741 with Vcc = 15V and VEE = -15V Rin = 2M ohm Rout = 75 ohm Open-loop Gain = 200000
Figure 3 shows a Hartley oscillator. Assume that the op-amp employed in the figure is an ideal op-amp, and R1= 20 kΩ, R2 = 60 kΩ, L1=10 mH. b) State the Barkhausen criterion for sustained oscillation.c) Explain briefly how the phase shift requirement for sustained oscillation ismet in the circuit of Figure 3.d) The feedback ratio and oscillation frequency of Figure 3 are givenrespectively by, B = -L2/L1 and w0 = 1 / sqrt(L1 +L2)C Determine the values of C and L2 in order for the circuit to oscillate at a frequency of 200 Hz.
Drive the following equation Vo=-11 Vin. Using summing amplifier RI circuit.
In the voltage regulator circuit shown in the figure, the op-amp is ideal. The BJT has VBE=0.7 V and Beta = 100, and the Zener voltage is 4.7 V. For a regulated output of 9 V, the value of R (in Ohms) is Express answers in two decimal points. Show solution on your answer sheet. V = 12 V Vo = 12 V 1 k2 1 k2 AV2 = 47 V %3D ww