A-Design a two-stage BJT amplifier as shown in the figure with coupling capacitors such that the 3 dB low frequencies associated with each stage are equal to 20 Hz. The transistor parameters are: ß = 200 and 1=5.21K. Vcc=5V RC= Rez 3.3.5 ΚΩ R₁ = 55 km2 R₁ = 55 kf2 R₂= R₂ = 31 452 31K52 R12 = S1k0 REL= 31102 Cc₂2

A-Design a two-stage BJT amplifier as shown in the figure with coupling capacitors such that the 3 dB low frequencies associated with each stage are equal to 20 Hz. The transistor parameters are: ß = 200 and 1=5.21K. Vcc=5V RC= Rez 3.3.5 ΚΩ R₁ = 55 km2 R₁ = 55 kf2 R₂= R₂ = 31 452 31K52 R12 = S1k0 REL= 31102 Cc₂2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q/ Use The following circuit to design an oscillator of 5KHZ out The amplifier used in this oscillators is multistage C.S with Source resistance amplifier. The design must be with minimum No. of stages. use The following FET Parameter Id=2MA, gm= 2.5ms and rds= 40K ohm use VDD=24volt. R
We examined the common source amplifier shown in the figure in the 5th experiment. The selection criterion of the input capacitance is Xcin = 0.1Rin: Calculate the required input capacitance value, Cin , if an input signal with a frequency of 2 kHz is applied. Şekitde gösterilen ortak source yükseltecini 5. deneyde incelemiştik Giriş kapasitesinin seçim kriteri Xcin - 0.1Rin dir. 2 kHzlik giriç sinyali için gerektt tapasite, Cm değerini hesaplayınız. Circuit parameters / Devre Parametreleri R1 = 53 k2, R, = 17 k2 R1 RD Cout Vout D VDD M2 Cin G Vin R2 RS cs O a. 74.19 nF O b. 86.55 nF O c. 49.46 nF O d. 61.82 nF O e. 43.28 nF
A piezoelectric force transducer has a charge sensitivity of 20 pC/N. It is connected to a charge amplifier and overall gain of transducer and amplifier is 50 mV/N. The gain of amplifier is O 2.5mV/pC O 1mV/pC O 1.5mV/pC O 4mV/pC
For the amplifier circuit given in figure below with (Rc = 1.6 k, RE1 = 0.6 k, RE2 = 0.6 %3D k, RF1 = 310 k, RF2 120 k, B=80, and Vcc = 18 v, determine %3D 1. Draw the AC equivelant re model of the amplifier 2. Calculate the input and output impedance 3. Calculate the voltage gain. Re RF, RF2 RE Riz
Q Figure be low For a Common shows the Ac eauivolent mid Freauen cy Source (Cs) E-MOSEET Voltage divider bias Gi ven' the E-MOS FET hibrid - II model (PF and Circuit at amplifier Circuit. Parameter : Gm - 2.43 ms rds Cas = LeF the outlut Wiring capacit qnce Cwo Vgs Ro RL lok 6or 2.2 he Vo gog.l Kse Us a) Determine the input impedance Zi and output impedance Zo b.) calculate the Voltage gain Av = Vo/vi at mid Freauehcy c.) calculate the two high cut-oFF and FHz, and determine Fre auoncy Freauencies FH1 the actual high cut-OFF FH
Design a three-stage amplifier that is impedance matched (use an emitter follower in stage 2) with an overall voltage gain of approximately 400. The phase of the input and output signal should be maintained. The amplifier should have a usable bandwidth of approximately 20MHz. As engineers you are expected to provide mathematical calculations, circuit diagrams and simulations in multisim software. The simulations should show a sample input signal, its output signal and frequency response plot of the three-stage amplifier.
Q2) for the amplifier shown in Figure 1) Determine the voltage gain (Av) and the current Gain (Ai) 2) Determine The input and output resistance 3) Determine The output voltage Vout 4) Draw The Ac load line 5) Draw the AC equivalent circuit 6) Determine the maximum input voltage (Vi(p-p)) for maximum output voltage (Vo(p-p)) without distortion. HH Vi-20 mv RB 56 kQ +₁ D B = 50 - 10 V HH RE 1kQ Vou RL • 10 Ω ww11
Use the following circuit to design an oscillator of 5 kHz output. The amplifier used in this oscillator is multistage C.S. with source resistance amplifier. The design must be with minimum No. of stages. Use the following FET parameters Id=2mA, gm=2.5 ms and rds = 40kN. Use VDD = 24V L R Vo Vi
A type II compensator implementation for the above Buck converter is shown below. Ce2 Vout Cet HH Ret Vctrl R2 E/A Vset What should be the voltage Vref in the above type II compensator to produce 5V DC output if R# = 4k and R2=1k. а. Vet b. Write the small signal gain equation (-ctrl) between Vetrl and Vout- out с. Does R2 present in the above gain equation. Please add some explanation. d. How many poles and how many zeros are produced by this type II compensator?
In the forllowing circuit, determine the value of the minimum base current required for saturation given that: Vcc = 12 V, VLED = 1.5 V, VCE(sat) 0.5 V , R. = 200 2, B,c = 50 +Vcc Ic Rc VLED ON ON RB Vin VCE 1s OFF Select one: a. 0.5 mA b. 4 mA C. 6 mA d. 1 mA
Signal-conditioning analysis shows that the following equation must relate output voltage to input voltage: Vout = 3Vin – 3V Design circuits to do this using (a) a summing amplifier and (b) a differential amplifier
In the voltage regulator circuit shown in the figure, the op-amp is ideal. The BJT has VBE=0.7 V and Beta = 100, and the Zener voltage is 4.7 V. For a regulated output of 9 V, the value of R (in Ohms) is Express answers in two decimal points. Show solution on your answer sheet. V = 12 V Vo = 12 V 1 k2 1 k2 AV2 = 47 V %3D ww