A DC Wheatstone bridge used in an electronic system is fed by 200V Battery as shown in figure Q19. The values of arm resistances are R1 = 10 Q, R2 = 10 Q and R3 = 20 2. Then, the output voltage Vout under bridge balance condition is calculated as, I Total I I2 R3 R1 + Vout (Vc-Vp) Vs C R4 R2 B. Figure Q19.

A DC Wheatstone bridge used in an electronic system is fed by 200V Battery as shown in figure Q19. The values of arm resistances are R1 = 10 Q, R2 = 10 Q and R3 = 20 2. Then, the output voltage Vout under bridge balance condition is calculated as, I Total I I2 R3 R1 + Vout (Vc-Vp) Vs C R4 R2 B. Figure Q19.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.30P: Reconsider Problem 3.29. If Va,VbandVc are a negative-sequence set, how would the voltage and...

See similar textbooks

Similar questions

A 120 Vp is applied to the primary coil of a center-tap transformer of turn ratio (n1 : n2 = 6: 2) . If the secondary coils are connected to a Ge diodes center-tap full wave rectifier, the output DC voltage is about __________. *1- 13.42 V2- 14.15 V3- 15.58 V4-12.54 V5- 16.23 V
Q1: Draw the d.c load line for the circuit shown in figure. NO SIGNAL VBB Vcc= 12.5 V www Re=2.5 k2
Refer to the circuit on the right. VEB = 0.7 V, when the BE junction is conducting. VECsat = 0.2 V B Vref = 2.2 V (Use two decimal places.) = ∞ VREF IL +5 V R LOAD Figure 2 a. What should be the value of R in ohms if IL is to be maintained at 146 mA under changing load conditions? b. In order to maintain this load current, what should be the maximum allowable load resistance in ohms?
3. Solve this by clamper circuit.
The neutral current is equal to three times of ....... sequence current.
Design a DC power supply using FWR to perform the following requirements. Find V_dc, V_rms, V-ripple, PIV of the diode. draw the waveform of (V_in, V_out, L_in, I_load, V_diode and I_diode). Input voltage = 25 Transformer turn ratio 0.1 load resistance = 1k ohm Ripple factor = 0.025 Diode type =Si
Consider a PV Module with 24 solar PV cells with the Size of each 15cm x 10cm are connected in series. Choose the correct statement for the above PV Module. (Assume necessary data) a. The output power is 2.25W and the output current is 0.09A b. The output power is 540W and the output current is 45A c. The output power is 54W and the output current is 2.25A d. The output power is 54W and the output current is 4.5A
Suppose line voltage may be as low as 105 Vrms or as high as 125 Vrms in a half- wave rectifier. With a 5;1 step-down transformer, the minimum peak load voltage is closest to O 29.7 V O 35.4 V O 25 V LEGO 21 V
Given the circuit below, compute for the following, (fin = 60Hz) a. Peak to peak ripple b. Filtered Vdc Si m Vs = 201peak si IKOS HOME
Q1. a) An SCR based AC power controller circuit is given in Figure 1. The circuit connects a 240V 50Hz AC source vi to a resistive load with resistance of 100. If the delay angle is a-15°, draw the waveforms of the load voltage Vo, and the voltage across SCR2. Calculate the power supplied to the load. + Vi Va + 2 SCR2 H₁₁ SCR₁ Figure 1 SCR based AC power control circuit Va + 2 io b) Figure 2 is a single phase 2-level voltage source converter (VSC) with a DC voltage Vd-200V. A PWM scheme, by comparing a reference value with a 10kHz triangle waveform, is used to control the switches S₁ and S2. The modulation index of the PWM is m=0.8. With the aid of graphs explain how pulse signals for the switches are generated, sketch the output voltage Vo, determine the duty cycle, and calculate the average output voltage. + Vo + Vo √ ₂ == Figure 2 A single phase VSC
Devices that pass the signal from its source to the measurement device without aphysical connection by using transformer, optical or capacitive coupling technique arecalled?Select one a. bridgesb. isolatorsc.filters d.rectifiers
H.W3 The single-phase full wave controlled rectifier has a R-L load with R= 0.552 and L= 6.5mH. The input voltage V, 220V at 50Hz. The delay angle is a-30, plot the input and output waveforms. Then determine: -The average thyristor current -The rms thyristor current -The output rms current -The average output current - The efficiency NOTE: Drive any formula that used in solution