A DC Wheatstone bridge shown in figure Q19, it fed by a battery of Vs = 150V. It is used to measure the value of unknown resistance of a resistor R4. The values of R1, R2 and R3 are 340 ohms, 250 ohms and 50 ohms respectively. Then, the output voltage Vout under bridge balance condition is calculated as, R, No Figure Q19 O a. OV O b. 1V O c 10V O d. 100V

A DC Wheatstone bridge shown in figure Q19, it fed by a battery of Vs = 150V. It is used to measure the value of unknown resistance of a resistor R4. The values of R1, R2 and R3 are 340 ohms, 250 ohms and 50 ohms respectively. Then, the output voltage Vout under bridge balance condition is calculated as, R, No Figure Q19 O a. OV O b. 1V O c 10V O d. 100V

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l33.2AI4RT3.582R116R210R3R420PTP1P2P3P4
In the circuit below, when a 2.2KN load is connected to the output, find the value of the current flowing through the R resistor (IR), the current passing through the zener diode (Iz) and the load current value (IL). Sigorta T1 Dr-De 1N4001 0,1A REGOLATOR D 220V AC Va-20V Vs AC Va 2200 De Vi-13V 15V 4700uF IN47448 Nominal Test Maximum Dynamic Impedance Maximum Reverse Zener Current Leakage Current Voltage) Vz @ IzT IZT ZT @ IzT ZZK @ IzK IZK IR Test Voltage VR V mA Ω Ω mA µA V 15 17 14 700 0.25 11.4 llle
R A IOLL 4) 2A A 2a R4 20V a) Find the voltage at point A due to the 20V source only. b) Find the voltage at point A due to the 2A current source only. c) Find the voltage at point A when both are activated.
H.w For the circuit show n figure ca Iculate the expre ss ion of tne assume t he in i tial value of in ductor .initial value of cap acit or is zero o'lf th o'5 F
In the circuit in the figure, the amplitude of the input current is 5 Amps and its phase is 0 degrees, the amplitude of the input voltage is 18 volts and its phase is 90 degrees. How many volts is the amplitude of the voltage phasor V on capacitor C1? Values of the elements in the circuit:R= 14 OhmsC1= 10j OhmsC2= -3j OhmsL= 4j Ohms
Determine the regulated output voltage of the circuit in Figure D IN4O02 Vour LM317 R 2402 D2 ADI IN4002 120 V ms 470uF 1.8 kQ 000
In Half Bridge arrangement of strain measurement, supply voltage is of 1.5 V and resistance of each arm is 110 ohms. The change in resistance will be 21 ohms and the gauge factor will be 3.8. Find a) output voltage in mV b) strain output voltage in mV Strain
OCX elp VCC VEE 6V 3V R2 A R1 2kQ 2kQ R5 2kQ a) Find the voltage at point A due to VCC only. b) Find the voltage at point A due to VEE only. c) Find the voltage at point A when both are activated.
Which of the following statements are correct for the circuit below? Thanks to the capacitors I – C1 and C2, the voltage gain of the circuit increases. II – Capacitors C1 and C2 are coupling capacitors and provide an isolation function between AC and DC voltages in the circuit. Thanks to the III – RE resistor, the voltage gain of the circuit increases. Thanks to the IV – RE resistor, the stability of the circuit increases. The V – C3 Capacitor is a bypass capacitor and prevents the loss of voltage gain. Capacitor VI – C3 is a coupling capacitor and has no effect on the voltage gain in the circuit. VII – As the value of the source internal resistance Rs increases, the voltage gain decreases. VIII – The voltage gain decreases as the value of any RL load to be added to the circuit increases
In circuit shown in figure, the operating point is chosen such that Ic 1.57 mA, VCE = 3.1V,If Rc = 2.5 KO, Vcc = 9 V and B = 49 %3D Determine the values of R1, R2 and Rg [VBE = 0.7 V and l = 10B] Rc R1 VCC RE R2 [5A www ww ww www
Consider four resistors in parallel connection: R1 = 3520.45 Q, R2 = 33.09 Q, R3 = 1484.22 Q and R4 = 11.83 Q. What is the equivalent resistance? R2 R3 R RT O 11.24 O 7.78 19.88 O 8.64 O 6.91
Perform the (v1-v2)/3 operation using an opamp.