A DC electrical circuit with a 24-volt power supply has two resistors in series of 150 ohms and 430 ohms.   What is the voltage drop across the 430 ohm resistor.

Q: There are three 15,000-ohm resistors connected in series across a 120-volt DC source.  What is the…

A: The solution can be achieved as follows.

Q: 2K 5V D1 etermine the voltage at the resistor R2. (assume LED forward voltage is 2.0 volts) m D3 R1

A:

Q: For the Cicuit shown 'in Figure Vcc sgV j Bc = 1-8 K^ ,=100 Zo=? Bc Ai = ?

A: Zo = 1.66kΩ  Zi = 733Ω  Re = 7.47Ω  Ai = 19.3

Q: A 12-volt battery is connected to a series circuit in which the inductance is 1-henry and the…

A:

Q: Two resistors 10 kilo-ohms and 90 kilo-ohms are connected in series across 3 Volts source. What is…

A:

Q: Determine the current flowing through resistor R1. (assume Zener voltage is 3 volts) * R2 1K R1 10V…

A: In this question,   We need to determine the current in the resistance R1  If Zener voltage is 3…

Q: Ques 2. Two coils connected in parallel across a 100V DC supply, take 10 A current from the supply.…

A:

Q: Determine the current flowing through resistor R2. (assume Zener voltage is 3 volts)

A:

Q: We want to make a resistivity measurement. How should we connect the probes of the multimeter? Drag…

A: a multimeter is a portable device that can be used to take various electrical measurements like,…

Q: 5. Three resistors A, B and C are connected in series to a 134-volt dc source. If the resistance at…

A: The obstruction offered to the flow of current is called resistance. The electrical component that…

Q: The figure shows an electric circuit which contains a double switch labelled by S. When the switch…

A: Given Switch at 11'  ,  II=6 A Switch at 22'  ,  III=6 A Switch at 33'  , ammeter reading ?

Q: When you connect a voltmeter to read a dc voltage   a. polarity is not important b. connect the…

A: In this question,  We need to choose the correct options When you connect a voltmeter to read a dc…

Q: The working of proportional and derivative controller with reference

A: 1- Proportional mode - P α eP=KpeKp=proportional gainP(s)=KpE(s) The band of errors where every…

Q: A PMMC instrument has a three resistor connected across it to design multi- ranges indirect method…

A: In this question we need to find the range of the ammeter and it circuit.

Q: A 25 watts, 120V has a cold resistance of 45 ohm. When the voltage is switched on, what is the…

A:

Q: Two 115-V incandescent lamps A & Bare connected in series across 230-V de source. Lamp A is rated…

A: This problem is related to circuit theory. This is based upon the concept of incandescent bulbs…

Q: In the circuit diagram below, determine on which terminal will you connect either ammeter or…

A: Given: Consider the given circuit: To find: Determine on which terminal will you connect either…

Q: What is the power dissipated by the 0.500-ohm load resistor that is connected to a 12.0-V emf with…

A: First we will find out voltage across load resistance.then We will find out power across load .

Q: 4.-For-labeled currents, draw an arrow to show the direction of the actual positive current. For…

A: Given labeled currents flow and labeled volatge polarities. we need to draw the actual positive…

Q: 18 R2 1K 5V D1 R1 1K Determine the current at LED, D2. (assume LED forward voltage is 2.1 volts) *

A:

Q: 3 Determine the voltage across the resistor R2. (assume LED forward voltage is 2.1 volts) * A R2 1K…

A:

Q: A PMMC type meter has a full scale deflection of 20 mA. The resistance of the coil is 400. So (1)…

A: Solution: PMMC type meter: full scale deflection i=20 mA                                  =20 ×10-3…

Q: A voltmeter that reads 0-100 volts has a 200-division on its scale that can be read up to…

A:

Q: Two 115-V incandescent lamps A & B are connected in series across 230-V dc source. Lamp A is rated…

A: Given

Q: Question: A battery is charged from a constant dc source of 220 V through a chopper. The dc battery…

A: First find the output voltage in each case and using input output voltage relation calculate duty…

Q: A power supply has a voltage regulation of 1 %.  If teh no-load voltage is 30 V, wat is teh…

A: Voltage regulation =no load voltage-full load voltagefull load voltage×100. Given vo load voltage…

Q: Can you help me Identify the nodes in electric circuit diagram in KCL and KVL

A: Introduction KVL (Kirchhoff's voltage law): Kirchhoff's voltage law states that algebraic sum of…

Q: What is the greatest voltage that can be applied across a -W, 2.7-MN resistor without causing it to…

A:

Q: In this lab, you will be using resistors of various nominal values. What are the 5-band colour codes…

A: Given resistor values are: 100 Ohm220 Ohm 390 Ohm 560 Ohm 1000 Ohm

Q: When a voltage of 100 volts at 50 Hz is applied to a series connection of a resistor A and an…

A: Given conditions are (i) When a voltage of 100 Volts at 50 Hz is applied to the resistor A and…

Q: In the circuit shown in figure, when the firing angle of thyristor T is 90 degree, what is the value…

A:

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.