A cylindrical tube of mean radius 1 in and wall thickness 0.1 in is subjected to an internal pressure p=300 psi and a torque T =2000 lb.in. The ends of the tube are closed. Find the safety factor against yielding if the material yields in uniaxial tension at SY =8 ksi and von Mises’ theory is used.

Q: Q.2. A helical torsion spring has a wire diameter of 0.038 in, outside diameter= 0.368, 8.5 coils in…

A:

Q: An open coiled heilcal spring made of 6 mm diam- eter steel wire and 60 mm mean coil diameter, with…

A: We know that an axial torque T is applied to an open coiled helical spring formed of 6 mm diameter…

Q: An cylinder is 30 cm in diameter and the steam pressure is 7 kg/cm. If the cylinder head is held by…

A:

Q: Find FOS as per goodman's realtion

A: Given data; Thin spherical pressure vessel having following data;   σ1=σ2=pr2t   (where;p=8, r=100…

Q: (1) A steel cylinder (Oyp = 260 MPa) of inner radius a and outer radius 3a is subjected to an in %3D…

A:

Q: closely coiled helical spring is made of 10 mm diameter steel wire, the mean diameter of  the coil…

A: Given:d=10 mmD=68.4 mmn=8G=100 KN/mm2P=807 N

Q: MPa . Assumin H/m² and Poisso hange in diamet

A: Given data  Dia of pressure vessel =650 mm Internal pressure = 14.7 Modulus of elasticity = 200 GPa…

Q: Q.3) For the shaft consist of two parts shown in figure. If shaft (1) has outside diameter doutl =…

A:

Q: calculate temperature change that will cause a tensile the stress of 90 MPa in the brass rod.

A: Given: Tensile stress =90 MPa To determine: The change in temperature

Q: Determine the maximum principal stress (Omax) at point H (MPa). she If th

A:

Q: Problem 3.9 A shaft composed of segments AC, CD, and DB is fastened to rigid supports and loaded as…

A:

Q: nal pressure, find wh able stresses for the

A:

Q: A bar of steel has the minimum properties Se= 40 kpsi, Sy = 60 kpsi, and Sut = 80 kpsi. The bar is…

A: Given:The endurance stress is The yield stress is The ultimate stress is The steady torsion stress…

Q: In the figure, a solid copper rod with an expansion coefficient aB = 165.107-1 / °C is 20 mm in…

A: To find: The stresses induced. Given: The diameter of the copper rod is dcu=20 mm1 m1000 mm=0.020 m.…

Q: Example 7.8: (Application of equation(7.42) for a thin hollow circular bar) (a) Obtain the value of…

A:

Q: 4. A thin-walled cylindrical tank with end caps, seen below, is acted on by an internal pressure p =…

A:

Q: Problem 3.20 Hollow shaft with D = 50 mm and d = 46 mm of L = 1m and G 83 GPa (steel). If the shaft…

A:

Q: A coil spring with 5 cm outside diameter is required to work under the load of 190 N. The wire…

A: Outside Diameter (D) = 5 cm = 50 mmWire Diameter (d) = 5 mm Active Coils = 6

Q: A copper tube with circular cross sectionhas length L = 1.25 m, thickness t = 2 mm, andshear modulus…

A: Consider figure given in the question for solution compose the connection for the inward…

Q: A rigid steel bar is supported by three rods, as shown. There is no strainin the rods before the…

A:

Q: 2 in in 1 in 8 3 in 3 in 3100 in in

A:

Q: A one mm diameter steel wire is wounded around a copper tube with external and internal diameters of…

A: Given: The diameter of wore, d = 1 mm The external diameter of tube, Do = 140 mm The internal…

Q: A motor driving a solid circular steel shaft transmits 30 kW to a gear at B (as shown). The…

A: Here is the solution for the above question.

Q: st internal pressure, find w allowable stresses for the y are reached simultaneo

A:

Q: For the bell crank shown in equilibrium in figure below, determine the normal and shearing stress of…

A: Given:Force acting on the bell crank, F=40 kNDiameter of the pin, d=20 mm

Q: Solid Mechanics  In the figure, solid copper rod with expansion coefficient αB = 165.10-7 1 / 0C It…

A: First of all, calculate the area of the steel pipe, Now, calculate area of the copper rod is,

Q: Two coaxial closed coil springs make up a standard compound helical spring. When both springs are…

A:

Q: A scuba tank is being designed for an internal pressure of 2,685 psi with a factor of safety of 2.0…

A:

Q: Q24 Find the stresses in each direction, also find the change in volume of the block of dimension…

A: Given data Where ‘T’ and ‘C’ represent tensile and compressive nature respectively.

Q: ckness of th SS yield stress SS = T A ga:

A:

Q: NQ1) A closed-end pressure vessel (d, = 300mm & t 10mm) is subjected to an internal pressure of…

A: Permissible stress is stress which produces due to pressure or forces which does not exceed the…

Q: Q6: A thin steel cylinder 1 m long, of 150 mm internal diameter and plate thickness of 5 mm, is…

A: Introduction: A thin cylindrical shell is also known as a pressure vessel, and these vessels are…

Q: Coefficient of expansion αB= 165.10^-7 1/ 0C , solid copper bar diameter 20 mm , It is placed in a…

A: From the given description: From continuity equation,

Q: (a) A thin steel cylinder 1.3 m long is subjected to internal pressure; the change in volume owing…

A:

Q: 6. A circular bar AB with ends fixed against rotation has a hole 25 in. 4 130 in ending for half of…

A:

Q: A solid brass bar of diameter d =1.25 in. issubjected to torques T1, as shown in part a of the…

A: d=1.25Applied troque on the solid bar be T1Allowable shear stress in the brass τa=12ksiPolar moment…

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.