A cylindrical body of 70 mm diameter and 150 mm length falls freely in a 80 mm diameter circular tube as shown in the figure below. If the space between the cylindrical body and the tube is filled with oil of viscosity 0.9 poise. Determine the weight of the body when it falls at a speed of 1.5 m/s. 80mm 70mm Cylindrical body Oil 150mm Circular. tube Oil

A cylindrical body of 70 mm diameter and 150 mm length falls freely in a 80 mm diameter circular tube as shown in the figure below. If the space between the cylindrical body and the tube is filled with oil of viscosity 0.9 poise. Determine the weight of the body when it falls at a speed of 1.5 m/s. 80mm 70mm Cylindrical body Oil 150mm Circular. tube Oil

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The surface tensions of mercury and water at 60 degrees Celcius are 0.47N/m and 0.0662 N/m, respectively. What capillary height changes will occur in these two fluids when they are in contact with air in a glass tube of radius 0.30mm? Use θ = 130° for mercury, and 0° for water; y = 132.3 kN/m3 for mercury and 9.650 kN/m3 for water. Provide the given along with its solution. (Please write legibly, I did not understand the first solution.)
Oil is allowed to flow in between two parallel plates. The distance between the plates is 0.0055 m. The lower plate has a velocity of 0.317 m/s while the top plate remains at rest. What is the shear stress expressed using English units? The viscosity of the oil is 0.03 Pa-s. Express your answers in 4 decimal places. Do not round off intermediate answers.
The block of weight W = 50 N is pulled by a weight W0 = 60 N along the surface of a table by means of an inextensible cable and a pulley. Between the block and the table there is a uniform layer of oil of viscosity m = 0.1 Pa-s and clearance h = 2 mm. The contact area is 0.01 m2. Find the terminal velocity U if the table is very long.
A thin plate is pulled at a speed V through a small gap of hieht h as shown in figure below. The space on both sides of the plate contains different types of fluids. Fixed wall H.H. y Oil ul Plate V (m/s) Oil µ2 Fixed wall Prove that the postion of the plate y takes the form: i. y= (H, +H2) When the shear forces are equal on the both sides of the palte. ii. y = When the drage force is minimum.
A square plate of mass 3 kg and side length 750 mm is placed on a flat plate inclined at 20° to the horizontal. An oil film exists on the plane and it is observed that the square plate slides down the plane at a velocity of 100 mm/s. If the thickness of the oil film is 0.1 mm determine the viscosity of the oil in poise.
The space between two square flat parallel plates is filled with oil. Each side of the plate is 0.8 m. The specific weight of the oil is 9620 N/m³. The thickness of the oil film is 14.9 mm and requires a force of 175 N. The liquid having the kinematic viscosity of 15 stokes. Determine (i) the shear stress (ii) the density of oil (iii) the dynamic viscosity in poise and (iv) the moving velocity of the upper plate. (i).Shear stress in N/m2 (ii). The density of oil in kg/m3 (iii).The dynamic viscosity in poise (iv). The moving velocity of the upper plate in m/s.
Find the force required to pull a shaft with diameter D, steadily into a sleeve with diameter D, and length L at a velocity of V. The clearance between the shaft and the sleeve is filled with an oil of viscosity μ.
a drop of water has a diameter of 2.5 mm. What is the surface tension in air if the pressure within the droplet is 0.8 kpa