A cylinder having a mass of 250 kg is to be supported by the cord that wraps over the pipe. Determine the largest vertical force F that can be applied to the cord without moving the cylinder. The cord passes (a) once over the pipe, ß = = 180 deg, and (b) two times over the pipe, ß = 540 deg. Take us = 0.2.

A cylinder having a mass of 250 kg is to be supported by the cord that wraps over the pipe. Determine the largest vertical force F that can be applied to the cord without moving the cylinder. The cord passes (a) once over the pipe, ß = = 180 deg, and (b) two times over the pipe, ß = 540 deg. Take us = 0.2.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The dimensions a = 2 m and b = 1 m. The couple M = 2400 N.m. The spring constant is k = 6000 N/m, and the spring would be unstretched if h = 0. The system is in equilibrium when h = 2 m and the beam is horizontal. Figure h M VF 1 of 1 Part A Determine the force F. (Figure 1) Express your answer with the appropriate units. F = Submit Part B 0 μA Value Az, Ay = Request Answer Units Determine the reactions at A. Enter your answers numerically separated by a comma. ? ΑΣΦ ↓1 vec
3. The force P applied to the brake handle enables the band brake to reduce the angular speed of a rotating drum. a) If P=340 N, determine the bigger tension on band brake. b) If P=340 N, determine the smaller tension on band brake. c) Determine the corresponding value of the braking torque acting on the drum. P u=0.2 0-2m R=0.225m 0.3m O• 15 m
A 90-kg smooth circular cylinder A with a radius of 0.6 m is held in equilibrium by a cord CD and a bar BC of negligible mass. The length of bar BC is 2.4 m. a. Draw the FBD of the circular cylinder and the bar BC.b. Determine the tension in the cord CD.
PROBLEM #3 Block A has a weight of 40 lb, and block B has a weight of 8 lb. The coefficient of kinetic friction between all surfaces of contact is = 0.15. Knowing = 20° and P= 50 lb, determine (a) the acceleration of block B, (b) the tension in the cord. A B et P
Hide bla Clear my choice A rigid beam is supported by a pin at A and two metallic wires at B and C. Determine the force P that causes the point C to displace downward by 0.3 mm. Given: E (wire B) = 70 Gpa, E (wire C) = 200 Gpa and both wires have a diameter D = 4 mm. Consider a linear elastic behavior. |-1 2 m 1.5 m A 3 m 2 m 2 m Select one: 11:49 PM A G d) ENG B
O A rectangular strip 50×15mm deep of brass is placed on top of another strip 50×15mm deep of steel to form a beam of 50×30 mm deep cross-section. The beam is supported across a span of 100 cm. Determine the magnitude of a point load that may be placed at its midspan if (a) The strips separate and bend independently E steel = = 2×10 MPa, Ebras = 0.9×10 MPa, stress are o steel Permissible = 150 MPa and o = 100 MPa brass 100 cm
3. The ball has a mass of 30 kg and a speed v = 4 m/s at the instant it is at its lowest point, 0 = 0°. Determine the tension in the cord and the rate at which the ball's speed is decreasing at the instant 0 = 20°. Neglect the size of the ball. 4 m
Question The electric motor exerts 600 Nm torque on the aluminum shaft ABCD when it is rotating at a constant speed. The torques exerted on pulleys B and C are as shown. 250 Nm 350 Nm 50 mm 40 mm 45 mm 1.1 m 0.9m a. Knowing that G = 16 GPa and B and C Section of the shaft is hollow with internal diameter of 30 mm. Determine the angle of twist between B and C. Provide the answer in degrees with precision to two decimal points. b. Knowing that G = 12 GPa for C and D part, and C and D Section of the shaft is solid. Determine the angle of twist between C and D. Provide the answer in degrees with precision to two decimal points.
Q:9/ A steel bar (50mm) in diameter and (2m) long is surrounded by a shell of cast iron (5mm) thick. Compute the load that will compress the combined bar a total of (1mm) in the length of (2m). For steel, (E=200*10° N/m), and for cast iron, (E=100*10° N/m²). Ans.(p=240KN)
üz a aplanmadı ) üzerinden etlenmiş y ioruyu etle Н V The internal shear force V at a certain section of a beam is 60 kN.m. If the beam has a cross-section shown in the figure where h=243 mm, a=112 mm, b=182 mm, c=10,8 mm and t=14,7 mm, Determine the first moment of area (Q) for the point H (mm) where L=48,2 mm.
5. Derive flexural formula and state the assumptions made while deriving flexural formula. 6. Draw the shear stress distribution across a circular section of diameter 20 mm, acting upon by a shear force of 30 kN. UNIT-III 7. Derive torsion formula and state the assumptions made in deriving torsion formula. 9. 8. A rectangular column of width 120 mm and of thickness 100 mm carries a point load of 120 KN. If the minimum stress at the base of the section is zero, find the eccentricity of the point load and also calculate maximum stress on the section. UNIT-V UNIT-IV A beam AB of span 6m is subjected to UDL of intensity 10KN/m. Determine the deflection of the beam at mid span and maximum deflection in terms of flexural rigidity. 1m 10 kN/m 3m oto 2m 10.A cantilever beam projection 2.5 m from a wall is loaded with a UDL of 80 KN. Determine the area moment of inertia of the beam section, if the deflection of beam at the free end be 8 mm. Take E = 200 GPa. Also determine the slope at the free…
ENGINEERING MECHANICS: STATICS (J.L.MERIAM) 2/8: Two forces are applied to the construction bracket as shown. Determine the angle o which makes the resultant of the two forces vertical. Determine the magnitude R of the resultant. F = 800 N F 425 N 70