Answered: A current in a 250 turn coil is 2.25A,…

A current in a 250 turn coil is 2.25A, wound in a core that has a reluctance of 12,000 AT/Wb. What is the resulting flux density (in Tesla), if the area of the core is 8cm²?

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter8: Basic Electric Motors

Section: Chapter Questions

Problem 3RQ

See similar textbooks

Related questions

Q: What will be the reluctance of a magnetic core if the mean path length for flux is 0.04 m and the…

A: We need to find out the reluctance for given details

Q: For the magnetic circuit shown in the figure, the iron core with N = 500 turns -Magnetic…

A: According to question: The cross sectional area is calculated as ∵a=πD24⇒a=π1×10-224⇒a=7.854×10-5m2…

Q: The value of current needed in 200 turns of figure Q3 to develop a flux of 0.6 mWb is?

A: Given Data: N = 200 turns flux = 0.6 mWb A = 2 * 10 ^-3 m2

Q: Draw the electrical circuit analog for the magnetic circuit shown in Figure P14.34. Pay special…

A: To draw the electrical circuit analog for the magnetic circuit shown in Figure P14.34. Now, to…

Q: For the electromagnet of Figure-a. Find the flux density in the core.b. Sketch the magnetic flux…

A: The magnetic flux density (B) is the ratio of magnetic flux (∅) to area of cross section (A) and…

Q: b. In the electromechanical system of the figure below, the iron portion has infinite permeability,…

Q: For the series magnetic circuit: • Find the value of I required to develop a magnetic flux of 4 x…

A: In this question we need to find a current to develop a magnetic flux of 0.4 mWb

Q: 10.A mild steel ring has a radius of 50 mm and a cross sectional area of 400 mm. A current of 0.5 A…

A: The solution is given below

Q: Draw the equivalent magnetic circuit, and calculate the values of the m.m.f. and all the…

A: The equivalent magnetic circuit:

Q: Assume that the magnetic core shown in the fig is made up of M19 29 gauge sheets with a cross…

A: Given information: The magnetic core shown in the fig is made up of M19 29 gauge sheets with a…

Q: 5) The magnetic circuit in the following figure has current 20 A in the coil of 5000 turns. Assume…

A: Given information i=20 A No. of turns, N=5000 Cross-section area, Ac=Ag=2 cm^2…

Q: The physical construction of two pairs of magnetically coupled coils is shown. Assume that the…

A: (a) The magnetically coupled coils are shown below: As per the direction of the fluxes, there are…

Q: In the magnetic circuit in the figure, the relative with a magnetic permeability of 2000 the…

Q: Using figures (a) and (b), a magnetic flux density of 0.1 Wb in the air gap Determine the current I…

Q: In figure, a magnetic flux of F is generated with a constant current of i The core material used has…

A: Given: For a magnetic circuit, Number of turns of the coil N=400, Current in the coil i=20 A,…

Q: (а) (i) , UTM Explain the term 'permeability' and what is the unit used? M TM (iii) Sketch suitable…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: A magnetic circuit consists of silicon steel of 3000 permeability and an air gap. The length of the…

A: MMF = H ×length MMF = NI Where N is number of turns and I is current in the coil. so find H in each…

Q: The reluctance of a non-magnetic path is 12 AT-Wb. Find the flux needed to be set up if surrounded…

Q: Q1- The magnetic circuit shown is made of a cast-steel and has a coil of 1000 turns on its 5cm and…

Q: EXAMPLE : For the series magnetic circuit of Figure a) Find the value of I required to develop a…

A: as you know by the formula, F (mmf) =ϕ(flux)×R(reluctance)R =LμAand F =Niso,Ni =ϕ×LμA----(1)μ =μ0μr…

Q: A magnetic circuit shown in FIGURE Q2 has a core relative permeability, µs = 2000. The depth of the…

A: Ans a) Rc1=Rc2=Rc3=lμ0μrA=0.1+0.2+0.14π×10-7×2000×10×40×10-4Rc1=Rc2=Rc3=15.915 KΩ Ans b) Reluctance…

Q: 1- For the series magnetic circuit of Figure below 4-2x 10- m2 N- 400 turns -Cast-steel core 1- 0.16…

A: The solution can be achieved as follows.

Q: The cross section of the core of a magnetic circuit with 100 relative permeability is 5 cm2 and the…

Q: A two-legged core is shown in figure below. The winding on the left leg of the core (N,) has 600…

A: Given that, N1=600 N2=200 i1=0.5 A i2=1 A μ=1000 We have to find total flux

Q: An electromagnet has an air gap of 3 mm length and the flux density in the gap is 1.257 T. Find the…

Q: For the circuit magnetic circuit above find the value of I required to establish a flux in the gap…

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: Question 1 A ferromagnetic core is shown in Figure 1. The depth of the core is 5 cm. The other…

Q: A dc machine has hysteresis loss of 300 W and an eddy current loss of 200 W when running at 1200…

A: Hysteresis loss Wh=300 W eddy current loss We=200 W The speed is N=1200 rpm Total core loss…

Q: The magnetic structure in the figure below is made of silicon steel. Determine the values of IB…

A: Note: Relative permeability (μr) for silicon steel is not given . We assume μr = 2000 Given NB=…

Q: square magnetic core has a mean path length 55cm and x-sectional area of 150cm2. A 200 turns coil of…

Q: The permeability of an annealed iron core is 5600 × 10-6 Tm/At when the current is 80 mA. The coil…

Q: 2. An air-gap between two pole pieces is 20 mm in length and the area of the flux path across the…

Q: Define the following: Flux density Coercive force Residual magnetism Saturation

Q: The resistance of the copper filed winding of a dc machine at 20 is 0.2 ohms. After operating the…

A: In this question we need to find a operating temperature of machine.

Q: or the magnetic circuit shown in the figure, the iron core with N = 500 turns -Magnetic permeability…

A: According to question: The cross sectional area is calculated as ∵a=πd24⇒a=π1×10-224⇒a=7.854×10-5m2…

Q: The magnetic core in Figure 3. has a mean core length of 80 cm, and its uniform cross-sectional area…

A: The solution is given below

Q: solenoid similar to the figure below, has a core made of cast steel (refer to the figure on the next…

Q: An electromagnet is used to support a solid piece of steel, as shown in the figure below. A force of…

Q: An iron core has a cross-sectional area of 10-3 square meter and mean circumference of 1 meter. The…

Q: A toroidal core with a mean circumference of 100 cm and a cross sectional area of 10 cm2 is wound…

Q: A 220 V series motor runs at 800 r.p.m., when taking a current of 15 A. The motor has R, = 0.3 Q…

A: A DC motor is a machine which takes DC electrical energy as an input and produces mechanical output…

Q: Consider the magnetic circuit in figure. A current of (3A) flows through 200 turns of wire around a…

A: (a) Let the magnetic circuit with air gap is shown below: Consider the neglecting leakage flux and…

Q: Q1. Figure 1 shows the magnetic circuit with cross section area of core, 1000 mm? and current…

A: *Keeping a note ?as per our company guidelines we are supposed to answer ?️only first 3️⃣ sub-parts.…

Q: Question 4 (a) A magnetic circuit shown in Figure Q4.a. The mild steel core has a mean length of 50…

A: The given magnetic circuit is shown below. Relative permeability is μr=2500 AT/m at flux density of…

Q: Calculate (A) the number of primary and secondary turns (B) the maximum value of flux density in…

A: In this we will find turns and maximum flux density of transformer....

Q: The resistance of the field winding(copper wire) of a DC machine is 0.25 ohm at 25°C. When operating…

A: In this question we need to find a resistance of the field winding at full load.

Q: A coil wound 3000 turns in the form of an air-cored torus with a square cross section. The inner…

A: Given,The number of turns is,N=3000The inner diameter of the torus is,Din = 60mmDin = 0.06mThe outer…

Q: 5. A mild steel closed magnetic circuit has a mean length of 75 mm and a cross-sectional area of…

A: Given data: l=75 mmA=320.2 mm2I=0.40 A a) The expression for the reluctance is given as,…

Q: 6. You have a complicated wire structure with an area of 1 cm², and an average interior magnetic…

A: Given data, Area, A=1 cm2 Magnetic field, B=10-9 T

Concept explainers

Synchronous Generator

In comparison to an asynchronous generator, it is a machine where the rotor speed is equal to the rotating magnetic field produced by the stator, i.e., mechanical speed is equal to the electrical speed, thus called synchronous, and not asynchronous.

Salient Pole Rotor

Salient pole rotor includes a large number of exposed poles mounted on a magnetic wheel. The construction of a bright pole is as shown in the image on the left. The proposed poles are made of metal laminations. The rotor winding is provided on these poles and is supported by pole shoes.

Question

A current in a 250 turn coil is 2.25A, wound in a core that has a reluctance of 12,000 AT/Wb. What is the resulting flux density (in Tesla), if the area of the core is 8cm²?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A toroidal core with a mean circumference of 100 cm and a cross-sectional area of 10 cm2 is wound with 500 turns of wire. What current would be required to generate a flux of 1 mWb in the core. Assume the core has a relative permeability of 800
An air core toroidal coil has 120 turns, the length is 12 cm and 12 sq. cm in area What is the current required to set up a flux of 1.2x10° weber. What is the current?
Using figures (a) and (b), a magnetic flux density of 0.1 Wb in the air gap Determine the current I in the coil with 200 turns required to produce
A magnetic circuit with a cross-sectional area of 20 cm? is to be operated at 50 Hz from a 120 V rms supply. The number of turns required to achieve a peak magnetic flux density of 1.8 T in the core is
A flux of 0.0016 Wb flows in a silicon sheet steel coil/core. The arrangement appears as shown below with the following dimensions: Ac = 0.0025 m? Core/gap area: Flux path length: le = 0.350 m lg = 0.0015 m N = 500 Air gap length: Number of turns: %3D A. What is the current, I, through the winding? B. What is the energy stored in the inductance? C. Assume that the current is given by i =9.75 sin (3147) A. What is the RMS voltage that would appear across the winding? D. Assume that the gap is removed from the arrangement with the flux path remaining at 0.350 m. For a flux of 0.0016 Wb, what is the inductance of the arrangement? E. What is the energy stored in the inductance with the gap removed?
An iron circuit with a small0.75 mm air gap is shown in Figure 1. A 6000 turn coil carries a current I = 18 mA which sets up a flux within the iron and across the air gap. The cross section of the iron is a consistent 0.8 cm2, and the mean length of the flux path is 0.15 m. a) Redraw the magnetic circuit using schematic symbols of an electric circuit with reluctance in each part of the circuit. b) State's Ohm's Law for magnetic circuit. c) By neglecting the effect of fringing, calculate the reluctance of the circuit. d) Find the flux within the core. N = 6000 Iron circuit (u, = 800 for iron). Figure 1
A 10, 120 V, 60 Hz supply is connected to the coil The coil has 200 turns. The parameters of the core are as follows: Length of core = 100 cm Cross-sectional area of core = 20 cm? Relative permeability of core = 2500 Obtain an expression for the flux density in the core.
An iron circuit with a small 0.75 mm air gap is shown in Figure 1. A 6000 turn coil carries a current I = 18 mA which sets up a flux within the iron and across the air gap. The cross section of the iron is a consistent 0.8 cm², and the mean length of the flux path is 0.15 m. a) Redraw the magnetic circuit using schematic symbols of an electric circuit with reluctance in each part of the circuit. b) State's Ohm's Law for magnetic circuit. c) By neglecting the effect of fringing, calculate the reluctance of the circuit. d) Find the flux within the core. N = 6000 Iron circuit (ur = 800 for iron).
An iron circuit with a small 0.75 mm air gap is shown in Figure 1. A 6000 turn coil carries a current I = 18 mA which sets up a flux within the iron and across the air gap. The cross section of the iron is a consistent 0.8 cm2, and the mean length of the flux path is 0.15 m. a) Redraw the magnetic circuit using schematic symbols of an electric circuit with reluctance in each part of the circuit. b) State's Ohm's Law for magnetic circuit. c) By neglecting the effect of fringing, calculate the reluctance of the circuit. d) Find the flux within the core. N = 6000 Iron circuit (4, = 800 for iron).
An iron circuit with a small 0.75 mm air gap is shown in Figure 1. A 6000 turn coil carries a current I = 18 mA which sets up a flux within the iron and across the air gap. The cross section of the iron is a consistent 0.8 cm?, and the mean length of the flux path is 0.15 m. a) Redraw the magnetic circuit using schematic symbols of an electric circuit with reluctance in each part of the circuit. b) State's Ohm's Law for magnetic circuit. c) By neglecting the effect of fringing, calculate the reluctance of the circuit. d) Find the flux within the core. N = 6000 Iron circuit (4, = 800 for iron). Figure 1
An iron core has a cross-sectional area of 10-3 square meter and mean circumference of 1 meter. The relative permeability of the material is 500 and the number of turns is 200. Determine the current required to set up a flux of 0.001 weber.
. An iron core has a cross-sectional area of 10-3 square meter and mean circumference of 1 meter. The relative permeability of the material is 500 and the number of turns is 200. Determine the current required to set up a flux of 0.001 weber. a. 7.54 A b. 7.96 A c. 8.19 A d. 8.47 A