A cross-sectional area of 322.58 mm of an aluminum bar which carries the axial loads applied at the positions shown in figure below. Find the total change in length of the bar if Modulus of elastic (E) = 68947.45 N/mm. Assume the bar is suitably fixed to prevent lateral buckling. 31.13 KN 22.24 KN 26.68 KN 17.79 KN 914.4 mm 1524 mm 1219.2 mm

Q: Define CMM.

A:

Q: Define Lateral movement

A: Lateral Movement: The movement of any body which is moving to any side of the body is known as…

Q: How do you convert gpm to ft?

A: A cross-sectional area's flow of fluid is measured in gallons per minute. In simple terms, it…

Q: 600 80 500 MPa 600- 10 psi 80 60 400 400 60 300 40 40 200 200 20 20 100 todos 0.005 0.05 0.10 0.15…

A: Given stress- strain diagram

Q: 2000 MPa 2000 1000 1000 0.000 0.005 0.010 0.015 Strain 0.000 0.020 0.040 0.060 0.080 Strain Stress…

A: Considering the given stress- strain graph the solutions are provided in the following steps-

Q: Define Eccentricity,

A: Eccentricity is a term is used in the loading condition of the engineering. for example, the load on…

Q: How is the punch list prepared?

A: A punch list can be defined as a document that is prepared when the project nears the completion and…

Q: The Vicatronic

A:

Q: I would appreciate it if you could explain what you mean when you say "GIS."

A:

Q: Write all the design data for a building design?

A: The design details are

Q: What is binder?

A: A binding agent, or binder, is a medium that is used as a way of supplying structural support to…

Q: The Write up is an opportunity to briefly answer the ASLA DISCOVER LANDSCAPE ARCHITECTURE BOOK FOR…

A: The ASLA Discover Landscape Architecture book for kids is a fun and educational resource that…

Q: With reference to the drawings,what is the order of precedence?

A: An order of precedence is listed to resolve any disputes that arise from the conflicts between the…

Q: Why are Construction Photographs needed?

A: There are various reason for the Need of construction photograph some of them are mentioned here:

Q: where did you get 6?

A: 6 is the loading intensity at B.

Q: What does the reductent diagram look like?

A: What does the reductent diagram look like?

Q: What is Third Party Certification?

A: When an item or organisation has the formal verification or authentication of certain…

Q: How can outdated structures progress?

A: The given question has asked 'how can outdated structures progress'? Old Structures  Old structures…

Q: How did you get the f'c?

A: Given, Fy = 420 MPa (tension) Fy = 414 MPa (compression)

Q: Can you show how to do part d I had the first 3 parts done before. I was confused with part D

A: In situ void ratio of top soil (et) = 0.47 Void ratio of borrow soil (eb) = 0.71

Q: 02: What is architectural drawing? Explain different views of a drawing.   Sir, please explain the…

A: Architectural drawings are the drawings that include technical data of the structural design of a…

Q: What are master specifications?

A: Master specifications are a compilation of standardized, guide specifications or pre-written…

Q: What are the steps involved in the construction of a control unit that employs vertical coding, and…

A: It has been asked in the question to determine the steps involved in the construction of a control…

Q: Plan the structural schematic layouts for various RC structural systems.

A: AutoCAD software is very useful software in the design and analysis of the structure or any…

Q: Explain what is project close out?

A: The term project closeout in construction is the last stage of a construction project and an…

Q: Describe what is Translational slides.

A: Translational slides:

Q: What exactly is computer-aided design (CAD)?

A: Computer aided design is main component of design of structures in Engineering.

Q: What is expert determination?

A: Experts are often assigned by justices and adjudicators in national courts and arbitration…

Q: Create a structure diagram that even individuals without technical knowledge may comprehend. In…

A: Solution: Let's assume the hospital to be a reference model for our structure. We are going to…

Q: What is vadose zone ?

A: Vadose zone or Unsaturated zone is the part of the earth that is above the fully saturated earth…

Q: How to identify if "cos" or "sin" is to be used?

A: If force makes angle with x-axis, cos component will be considered along x-axis and sin component…

Q: Hello! Would it be possible to included a step by step solution without skipping something and add…

A:

Q: What are the Scheduling Changes?

A: Scheduling in construction projects is defined as the process in which the tasks, activities and…

Q: Who created the drawing?  AW?

A: Engineering drawing is used to illustrate the necessary details of any member. It is used by…

Q: Write a few lines on RFI?

A: Request for information is a process of business in which the main motto is  to collect the…

Q: What is the arch dam?

A: Arch dam: It is a curved concrete dam, convex upstream and resists force acting upon it mainly by…

Q: What is used to mark the tape lengths?

A: In surveying, tapes are used to measure distances that are level, vertical, or sloping. Tapes are…

Q: MAY 30 For the truss shown below disregarding the weight of the structure: 20 KN All vertical…

A:

Q: Can you please solve the number 2 question in the picture? Thank you

A:

Q: Discuss Construction Methods

A: The various methods used in the construction industry with specific design and planning so as to…

Q: In addition to furnishings, give the list of other equipment required by the owners,and engineers?

A: The owner shall supply all owner-furnished equipment to the Project for installation by EPC…

Q: What is the CSI Project manual?

A: The CSI Project Manual is the authoritative resource for organisation, preparation, use and…