A crate of 69 kg simply stands on the moving cart with constant acceleration a. The height from the center of gravity to the cart, L, is 1.4 m, and the angle = 13°. What is the maximum acceleration a (in m/s²) the cart can have without sliding on the cart? The coefficient of static friction between the crate and the cart is g = 0.51. Please pay attention: the numbers may change since they are randomized. Your answer must include 3 places after the decimal point. Take g = 9.81 m/s². 0.5 m 0.5 m Your Answer: • G 0 Answer

A crate of 69 kg simply stands on the moving cart with constant acceleration a. The height from the center of gravity to the cart, L, is 1.4 m, and the angle = 13°. What is the maximum acceleration a (in m/s²) the cart can have without sliding on the cart? The coefficient of static friction between the crate and the cart is g = 0.51. Please pay attention: the numbers may change since they are randomized. Your answer must include 3 places after the decimal point. Take g = 9.81 m/s². 0.5 m 0.5 m Your Answer: • G 0 Answer

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.3P: Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair...

See similar textbooks

Similar questions

A wedge is used to prop up the 6000-lb block of marble. The wedge angle is =30, and the angle of static friction is s=12 between all contact surfaces. Determine the smallest force P that would prevent the wedge from sliding out.
Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
The normal pressure acting on the disk of the sander is given by p=(4/3)+(r2/6), where p is the pressure in pounds per square inch (psi) and r represents the radial distance in inches. Determine the torque C required to operate the sander at constant speed if the kinetic coefficient of friction for the surface being sanded is 0.86.
The weight of the cylindrical tank is negligible in comparison to the weight of water it contains (water weighs 62.4lb/ft3). The coefficient of static friction between the tank and the horizontal surface is s. (a) Assuming a full tank, find the smallest force P required to tip the tank, and the smallest s that would allow tipping to take place. (b) If the force P = 200 lb initiates tipping, determine the depth of water in the tank.
How many turns of rope around the capstan are needed for the 40-lb force to resist the 8000-lb pull of a docked ship? The static coefficient of friction between the capstan and the rope is 0.25.
The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016, determine the force F required to advance the bar at a constant speed.
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
A crate of 68 kg simply stands on the moving cart with constant acceleration a. The height from the center of gravity to the cart, L, is 1.5 m, and the angle 0= 13°. What is the maximum acceleration a (in m/s²) the cart can have without tipping over on the cart? The coefficient of static friction between the crate and the cart is ls = 0.49. Please pay attention: the numbers may change since they are randomized. Your answer must include 3 places after the decimal point. Take g = 9.81 m/s2. 0.5 m |0.5 m G a Your Answer: Answer
The man in given figure is trying to move a packing crate across the floor by applying a horizontal force P. The center of gravity of the 250-N crate is located at its geometric center. Does the crate move if P =60 N? The coefficient of static friction between the crate and the floor is 0.3.
A 250 lb refrigerator is being pushed. You do not know what force P should be applied. The coefficient of static friction between the refrigerator and floor is lg = 0.4. The center of gravity of the refrigerator is at point G. - d2 -- d2 F1 d3 d1 d4 Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value di 4.5 ft d2 1.5 ft d3 2.5 d4 3.5 a. Determine the force P that is needed to overcome friction. b. Determine the location of the normal force r measured from the center of the refrigerator if the force P from part a is applied. c. Determine the minimum force P that is required to tip the refrigerator. d. Will the refrigerator slip or tip first? Round your final answers to 3 significant digits/figures. P= lb ft Pip = lb Will the refrigerator slip or tip first? tip O slip
A carnival ride has people stand inside a vertical cylinder with their backs to the wall. The cylinder starts spinning and the riders find that they are “stuck” to the wall and don’t slide down, even if the floor is removed. The ride has a radius of r. The person has a mass of m and is moving with a constant speed of v. The coefficient of static friction between the person and the wall is μs , and kinetic friction μk. The person is only touching the wall, not touching the floor. What is the magnitude of the acceleration of the person? In what direction does it point? The speed is constant. Why is the acceleration not zero? Briefly explain. No equations!
The height of the g point is 0.5m, the distance of the rear wheel to theg point is 1.75m, the distance of the front wheel to the g point is 1.8 m, and the car with a mass of 2100kg brakes suddenly while moving at 24v speed. l-Find the friction coefficient between the wheel and the road? 2-Find the way the vehicle takes until it stops?