A copper wire has a density of 8920 kg per cubic meter, a radius of 1.5mm and an unknown length. The wire is held under a tension of 12N. transverse waves are sent through the wire, (a) determine the linear density of the wire, (b) determine the speed through which wave travel through the wire. *

Q: solve and show every step with right answer

A: Data given - Rectangular cross section 225×75 mm2 Torsional moment = 20kN Axial Compressive force =…

Q: Show your complete solution including the diagrams and box your final answers with their appropriate…

A:

Q: The cylindrical gasoline tank on a tractor is 11 inches in diameter and 36 inches long. How many…

A:

Q: Please click on the point in the heating curve where the vapor pressure is equal to the external…

A: When vapor pressure becomes equal to external pressure, bubble formation takes place inside the…

Q: not read the answer. Is there a way to upload it in ano

A: Navier-stokes equation (momentum and continuity equations)

Q: Problem 1: a) Draw the free body diagram of the member ABC? b) Determine the reaction forces at the…

A:

Q: Metalworking According to standard American wire size tables, 3/0 wire is 0.4096 inches in…

A: Given: 3/0 wire is 0.4096 inches in diameter To  find: Write this size to the nearest 32nd of an…

Q: Compute the moments of inertia with respect to the X-X and Y-Y centroidal axes for the following…

A:

Q: S) t) What is the distance, d3x, of shape 3's centroid from axis Xo? What is the distance, d6x, of…

A:

Q: solve by showing every step.

A: Given data: The ultimate tensile strength of component is Sut = 30 ksi. The ultimate compression…

Q: SA5) What is the momentum of a vehicle if a force of 1000 N is applied on it in 0.50 seconds if it…

A: Given : F  = 1000 N             t = 0.50 sec To find : momentum of a vehicle

Q: I need question 7 answered pertaining to the print provided. I asked this question previously on…

A: 7. According to ASME, the revision can be made either by making the changes in the revision block or…

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: 2. From the given figure below, solve for the bar Y from the reference line. (choose the nearest…

A:

Q: QI: Write an algorithm to find the average of three marks. Q2: write an algorithm to print the…

A: We need to write the algorithm for two problems

Q: Completely solve and illustrate the problem. Show what are given, required, illustration, analysis…

A: given; diameter of solid shaft(ds)=4.2in                                       =0.1068mweight of…

Q: You are in an inventory management field these days.  You are working for a place which works on 365…

A: The objective of this question is to determine the number of orders per year that should be placed…

Q: A seesaw that weights 45lbs and its 5m long is balanced on the fulcrum in the center.  1- Two…

A: Given Data, W = Weight of the seesaw = 45 lb L = Length of the seesaw = 5 m Condition 1 :-…

Q: of the table) and free to move if a force is applied. A force is applied on it as the arrow…

A:

Q: for this question just sketch what it should look like:

A: Note : Window is denoted by point P

Q: a powerp u, a process design id wastes (MSW) per hour. In an industrial boiler, MSW is burned to…

A: To given thatH1=104.93Kj/kgH2=2675.53kJ/kgH3=2942.73kJ/kgH4=3324.63kJ/kg

Q: SHOW YOUR COMPLETE SOLUTION AND BOX YOUR FINAL ANSWER WITH PROPER UNITS. DO NOT ROUND OFF UNTIL YOU…

A: Note: As per Bartleby guidelines, we can only answer first 3 sub parts. Kindly re post the other…

Q: Question 5 The force F in Figure A is to be replaced by a force through A and a couple whose forces…

A:

Q: Please use different values. This answer you already gave me for a similar question. These values I…

A:

Q: a) Solve for ox'. Express your answer in kilopounds per square inch to three significant figures. b)…

A:

Q: 1.3 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A: Sure, based on the information provided in the text accompanying the image, the angle between lines…

Q: In a hot water heating

A:

Q: Find the value of P

A: Need to find Values of P

Q: I need these 3 parts answered. In manufacturing, dimensions often may fall in a range. For example,…

A: 1-In manufacturing, dimensions often may fall in a range. For example, for three-place decimals, the…

Q: The impact test is used to find a material's it's ability to absorb energy before it fractures. O.…

A: About impact test. Impact test is used to determine the dynamic toughness material. In this test a…

Q: A closed cylindrical vessel contains a fluid pressure of P (Mpa). The cylinder has an inside…

A: Given:Syt=340 MPad=2.5 mt=31.8 mmN=2.5

Q: The steel wide-flange beam has the dimensions shown. If it is made of an elastic perfectly plastic…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked .…

Q: The Answer is cut off on the right side.

A:

Q: An 4 cylinder engine has a crankshaft sp of 3,500 rpm, a bore of 3.8 inches, a str of 3.8 inches,…

A: Givenk=4N=3500 rpmd=3.8in =3.8×0.0254=0.09652mL=3.8in=3.8×0.0254=0.09652mP=210…

Q: I will rate you with “UPVOTE/LIKE” if you answer every question.   I will rate you with “DOWNVOTE/

A: Given Data : Definitions Moment Principle

Q: 1- Sketch front, right and top views of the following object. Each grid represents 10 mm. Front

A: Given: Sketch Front, top and right side view of the given isometric view.

Q: Two lenses are shown in the following figures. The one shown in figure 1 is thinner from the edges…

A: Data given-  For lens - 1 : thinner from the edges and thicker in the middle  Lens-2 : thicker from…

Q: Drive Shaft Outlet Blades Inlet Scroll Impeller

A: IMPELLER FAN A fan impeller is ordinarily joined to the turning shaft. Outer rotor engines basically…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.