A copper block of volume 1 L is heat treated at 500ºC and now cooled in a 200-L oil bath initially at 20◦C. Assuming no heat transfer with the surroundings, what is the final temperature?

Substance X is known to exist at 1atm in the solid, liquid, or vapor phase, depending on the temperature. Additionally, the values of these other properties of X have been determined (picture). You may also assume X behaves as an ideal gas in the vapor phase. Suppose a small sample of X at -20°C is put into an evacuated flask and heated at a constant rate until 10 kJ/mol of heat has been added to the sample. Graph the temperature of the sample that would be observed during this experiment.

Calculate the amount of heat needed to raise the temperature of 55.0 g of liquid water from 25°C to 99°C. The specific heat of liquid water is 1.00 cal/g °C

Please don't provide handwritten solution ....

A pure sample of Substance S is put into an evacuated flask. The flask is then heated steadily and the temperature measured as time passes. The results are graphed below, in the middle (in green). Identical experiments are now run on Substance Y and Substance Z. Substance Y is just like S except that it has a higher heat capacity in the solid phase C₂ (s). Substance Z is just like S except that it has a lower enthalpy of vaporization H. Select the graphs below, on the left and right, that show the results you expect for these new experiments. Substance Y •C₁ (s)) (higher Cp (Drag the slider to choose an image) temperature (°C) Substance S added heat (kJ/mol) Substance Z (lower H₂) (Drag the slider to choose an image) ³ 5

An industrial process for manufacturing sulfuric acid, H2SO4, uses hydrogen sulfide, H2S, from the purification of natural gas.  In the first step of this process, the hydrogen sulfide is burned to obtain sulfur dioxide, SO2. 2H2S(g) + 3 O2(g) → 2 H2O(l) + 2 SO2(g); ∆H = -1124 kJ.  The density of sulfur dioxide at 25 °C and 1.00 atm is 2.62 g/L, and the molar heat capacity is 30.2 J/mol °C. a) How much heat would be evolved in producing 1.00 L of SO2 at 25 °C and 1.00 atm?  b) Suppose heat from this reaction is used to heat 1.00 L of SO2 from 25 °C to 500 °C for its use in the next step of the process.  What percentage of the heat evolved is required for this?

What amount of heat (in kJ) is required to convert 10.8 g of an unknown liquid (MM = 83.21 g/mol) at 19.2 °C to a gas at 93.5 °C? (specific heat capacity of liquid = 1.58 J/g. °C; specific heat capacity of gas = 0.932 J/g⋅ °C; AHvap = 22.5 kJ/mol; normal boiling point, Tb = 57.3 °C)

A 5.0 g block of metal is heated to 124 °C and added to 145 mL of H2O, initially at 20.4 °C. if the metal is copper, what is the final temperature of the water?

A 0.580 g0.580 g sample of steam at 107.3 ∘C107.3⁢ ∘C is condensed into a container with 4.56 g4.56 g of water at 17.0 ∘C.17.0⁢ ∘C. What is the final temperature of the water mixture if no heat is lost? The specific heat of water is 4.18  J g⋅ ∘C,4.18  J g⋅ ∘C, the specific heat of steam is 2.01  J g⋅ ∘C,2.01  J g⋅ ∘C, and Δ?vap=40.7 kJ/mol.

As a substance is subjected to pressure and/or temperature changes, it may undergo condensation, deposition, freezing, melting, sublimation, or vaporization. (a) Consider the phase diagram shown below and state the cha nges that take place upon going from points A to B to C to D. (b) Is the transition from C to D exothermic or endothermic?