A continuous and aligned fiber-reinforced composite having a cross-sectional area of 1200 mm² is subjected to an external tensile load. If the stresses sustained by the fiber and matrix phases are 152 and 2.27 MPa, respectively, the force sustained by the fiber phase is 72300 N, and the total longitudinal strain is 0.00143, determine the following: (a) The force sustained by the matrix phase (in N). (b) The modulus of elasticity of the composite material in the longitudinal direction (in GPa). i N i (c) The modulus of elasticity for the fiber phase (in GPa). GPa i GPa (d) The modulus of elasticity for the matrix phase (in GPa). GPa

A continuous and aligned fiber-reinforced composite having a cross-sectional area of 1200 mm² is subjected to an external tensile load. If the stresses sustained by the fiber and matrix phases are 152 and 2.27 MPa, respectively, the force sustained by the fiber phase is 72300 N, and the total longitudinal strain is 0.00143, determine the following: (a) The force sustained by the matrix phase (in N). (b) The modulus of elasticity of the composite material in the longitudinal direction (in GPa). i N i (c) The modulus of elasticity for the fiber phase (in GPa). GPa i GPa (d) The modulus of elasticity for the matrix phase (in GPa). GPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A continuous and aligned fibrous reinforced composite having a cross-sectional area of 975 mm, then the area is subjectedi to an extenal tensile load. If the stresses sustained by the fibre and matrix phases are 215 MPa and 5.38 MPa, respectively, the force sustained by the fibre phase is 76,800 N, and the total longitudinal composite strain is 1.56x103 then determine.
(b) A continuous and aligned fiber-reinforced composite is to be produced using 45 vol% of aramid fibers and 55 vol% of polycarbonate matrix. Mechanical properties of these two materials that are given in Table Q5(b): Table Q5(b): Mechanical properties of fiber and matrix Modulus of Elasticity (GPa) Tensile Strength (MPa) Aramid Fiber 131 3600 Polycarbonate 2.4 65 If the stress on the polycarbonate matrix is 35 MPa, when the aramid fibers fail, then compute the followings: (i) the longitudinal tensile strength (ii) the longitudinal modulus of elasticity
1. An element of graphite-reinforced composite is completely dry and is constrained against any dimensional changes in the 1 and 2 directions, but it is free to expand in the 3 direction. The element absorbs 1.5% of its dry weight in the form of moisture. (a) What is the strain in the 3 direction as a result of the moisture absorption? Why is this strain different from the value given by B3AM? (b) What stresses develop in the element? Assume that moisture absorption does not influence the material properties.
Consider a graphite-reinforced polymer composite lamina. Use the simple rule-of-mixtures formulas to calculate the values of the four elastic constants E1, V12, E2, and G12 for the lamina. Use V₁= 0.6. Assume the following material properties for the matrix and fibers. Em 4.62 GPa, E = 233 GPa, E = 23.1 GPa, G₁₂ = 8.96 GPa m = 0.360 2 = 0.200 3 = 0.400 G3 = 8.27 GPa
At an axial load of 24 kN, a 35-mm-wide by 15- mm-thick polyimide polymer bar elongates 3.0 mm while the bar width contracts 0.15 mm. The bar is 230 mm long. At the 24-kN load, the stress in the polymer bar is less than its proportional limit. Determine (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar thickness. Answers: E= = V = IN Athickness= i GPa mm
At an axial load of 25 kN, a 50-mm-wide by 20-mm-thick polyimide polymer bar elongates 2.8 mm while the bar width contracts 0.29 mm. The bar is 190 mm long. At the 25-kN load, the stress in the polymer bar is less than its proportional limit. Determine (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar thickness. Answers: (a) E= (b) v= (c) Athickness= i i GPa mm
Q2: A fiberglass composite consists of a matrix of vinyl ester and reinforcing fibers of E-glass. The volume fraction of E-glass is 30%. The density of the vinyl estiser 0.882 g/cm³, and its modulus of elasticity is 3.6 GPa. The density of E-glass is 2.6 g/cm³, and its modulus of elasticity is 76 GPa. A section of composite 1 cm by 25 cm by 2 m is fabricated with the E-glass fibers running longitudinally in the 2000 mm direction. Determine: (a) The masses of vinyl ester and E-glass fibers. (b) The density of the composite. (c) The composite modulus of elasticity in the longitudinal and the perpendicular directions of the glass fibers. (d) If the tensile strength of the glass fibers, is 1 GPA and the tensile strength of the epoxy matrix is 60 MPa, find the tensile strength of the composite in the longitudinal direction.
An aligned and continuous glass fiber-reinforced epoxy composite consisting of 55 vol% glass fibers has a cross-sectional area of 420 mm2. The composite is subjected to a longitudinal load of 61,300 N. Calculate the magnitude of the stress on matrix phase if the elastic moduli of the glass fiber and the epoxy are 165 GPa and 5.7 GPa, respectively.
ii) A continuous and aligned glass fiber-reinforced composite consist of 40 vol% of glass fibers having a modulus of elasticity of 69 GPa and 60 vol% of polyester resin that, when hardened, displays a modulus of 3.4 GPa. Find the modulus of elasticity of this composite in the longitudinal direction.
Consider a graphite-reinforced polymer composite lamina. Plot the graph of each elastic constant (E1, V12, E2, and G₁2) versus the fiber volume fraction V. Use all values of V, ranging from 0 to 1 (in increments of 0.1). Assume the following material properties for the matrix and fibers. Em 4.62 GPa, E{ = 233 GPa, E = 23.1 GPa, G₁₂ = = 8.96 GPa = vm = 0.360 v2 = 0.200 123 = 0.400 G₁3 = 8.27 GPa
RT 80 -20 °C -60 °C 60 40 20 0.005 0.01 0.015 0.02 Strain HW: Determine the YS of glass/epoxy composites at the three temperatures shown. Also determine the YS at -10°C. Transverse tensile stress (MPa)
A polymer sample of height 700 cm with an area of 6 m2 supports a mass of 70 tons. Youngs modulus of the polymer sample is found to be 60 GPa. Calculate the change in height of the polymer sample, applied stress and strain.