A consumer has a work area that he wishes to illuminate with single 80W, 220V tungsten fitting. The existing light points, which are to be removed are controlled by a single gang 10A switch. This switch is to remain in the design. How many light fittings will the switch support. A-Current consumed by one fitting is B-The switch must carry the current of C-Number of fitting supported by the switch is

A consumer has a work area that he wishes to illuminate with single 80W, 220V tungsten fitting. The existing light points, which are to be removed are controlled by a single gang 10A switch. This switch is to remain in the design. How many light fittings will the switch support. A-Current consumed by one fitting is B-The switch must carry the current of C-Number of fitting supported by the switch is

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter5: Components, Symbols, And Circuitry Of Air-conditioning Wiring Diagrams

Section: Chapter Questions

Problem 13RQ: Identify the following symbols for switches:

See similar textbooks

Similar questions

QUESTION 5 We would like to run the power wires for both cooling pumps in the same RMC from the Breaker panel to a junction box above the control panel. What size ungrounded conductors do we need for the 100 amp load? All conductors have typeTHHN insulation. A #6 AWG B #3 AWG C #4 AWG D #1 AWG
What is the correct way to measure current in a completed circuit using a DMM? O Connected in series to the circuit being tested. O Connected in parallel to the circuit being tested. Connected across the load device in the circuit being tested. Connected in placed of the load device in the circuit being tested.
leaving a freevway. Current from the opposite side must travel further, weakening the potential on that side. This creates a potent the motor in that direction, causing the motor to spin. O Only the side where the switch is closed forms a cormplete circuit, so the motor must spin in that direction. Answer the questions and submit the photos for questions 2 -9using the circuit from STEP 2. D2 Yellow R1 50 Q R2 50 0 R3 PSB (+ 5 V 100 aLW R4 D1 100 Q Blue SW1 Sw2 Question 2 本
Determine the voltage at the resistor R2. (assume LED forward voltage is 2.0 volts)
Identify the following symbols for switches:
Discuss the types of oil circuit breakers. Please write more answer
There are two types of switch's in the electrical circuit attached . What is the state of each type and what is the difference between them?
Set VA to 20 volts. Insert a jumper between points A and B. 1.Charge time was approximately how many seconds? 2.One RC time is approximately how many seconds? 3.The Re of the meter and the 1-m ohm resistor is approximately how many ohms?
Task: Add another potentiometer with voltage divider to control another diode led manually. Code Explanation: please help me with the code required
Module 10 Section Review 3.0.0.png Additional Resources Electronics Fundamentals: Circuits, Devices, and Applications, Principles of Electric Circuits, Thomas L. Floyd. New York: Prent 3.0.0 Section Review 1. The letter designation SL on an electrical draw- ing indicates a 4. A a. a. limit switch b. low-voltage switch c. load switch d. light switch b. C. d. 2. Existing power lines on an electrical site plan may be indicated by the letter 5. In t safe a. E b. I a. b. 2 С. Р d. V C. 2 d. 2: 3. The specific types of luminaires required in an installation can be found on the a. power plan b. electrical site plan c. schematic diagram d. lighting fixture schedule P Search for anything
Q. What will be the status of switch S1 and S2 for which the LED glows. The circuit diagram is attached here. PLEASE TELL THE COMPLETE SOLUTION.
What is the formula used to find the peak voltage of 100 volts effective? A. Peak voltage = .707 x 100. B. Peak voltage = .9 x 100. C. Peak voltage = 1.414 x 100. D. None of the above.