A concrete crusher has been purchased for $60,000 and it has an estimated salvage value of $10,000 at the end of its five years life. Engineers have estimated the following units of production of crushed materials over the next five year 1 2 3 4 End of year Crushed Material m³ 16,000 24,000 36,000 16,000 5 8,000 What is the total depreciation at end of year 3 and what is the book value at end of year 2 ?

A concrete crusher has been purchased for $60,000 and it has an estimated salvage value of $10,000 at the end of its five years life. Engineers have estimated the following units of production of crushed materials over the next five year 1 2 3 4 End of year Crushed Material m³ 16,000 24,000 36,000 16,000 5 8,000 What is the total depreciation at end of year 3 and what is the book value at end of year 2 ?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the tonnage or capacity/truck using the following parameters: Ore hauling Cycle time = 30 minutes hauling time = 18 hrs/day Production target = 30,000 tons per day Truck Capacity = 100 tonner Truck factor = 85 %
For the beam shown, the magnitude of the concentrated load is P = 11 kN, the magnitude of the couple is MB = 190 kN-m, and the beam lengths are a = 4.9 m and b= 14.7 m. (a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point. A. (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the magnitudes of the maximum shear force and the maximum bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. A MB B b C X
A cement grinding mill "A" with a capacity of 50 tons per hour employs P12,000 per tonforged steel grinding balls with a wear rate of 100 grams per ton of cement processed.Another cement mill of the same capacity, "B," utilizes P50,000 per ton high chromesteel grinding balls with a wear rate of 20 grams per ton of cement processed.Determine the more cost-effective grinding mill, keeping all other factors constant. do not use excel, use formula
Please show step by step calculation of each value
PLease answer the question in the picture please, show all of your work please and post pictures of your work, Do not type it!
I want the solution in less than 15 minutes
I need the answer as soon as possible
The aggregate used in road construction begins degrading integrity of said roadway when pieces begin exceeding 23.5 millimeters in diameter. Any pieces smaller than 23.5mm in diameter are fine. The recently delivered load of aggregate being used has a 19mm mean and 5.5mm standard deviation. What is the Z value to two decimal places?
Referring to the aggregate gradations A, B, and C in Figure , answer the following questions:a. What is the maximum size of each gradation?b. What is the nominal maximum size of each gradation?c. Classify each gradation as dense, open, or gap indicating the reason for each classification.
45 1. 2. Given the following two aggregate gradations shown in Table 1. plot individually on a semi-log scale and determine which ASTM C33 size number is appropriate for each. Give the following two aggregate gradations shown in Table 1, determine the best combined aggregate gradation using a 45 power curve. Include a neat, well-organized spreadsheet with at least three possible combinations in addition to the original gradations and state which combination you think is the most well-graded. Table 1. Aggregates for blending Sieve 1 in. % in. ½ in. 3/8 in. #4 #8 # 16 # 30 # 50 # 100 Percent Passing 100 80 60 80 40 60 20 40 20 0 Percent Passing 100 Aggregate 1 (% passing) 0 100 100 68 41 6 3.0 2.3 2.1 2.0 1.9 Aggregate 2 (% passing) 100 100 100 100 99 93 76 2 3 Sieve Size Raised to 0.45 Power Figure 1. Basis of 0.45 Power Chart (Source: Asphalt Institute SP-2) 45 14 1 Example: 4.75 mm sieve plots at (4.75) 0.45 = 2.02 OREK) ۹:۰۰ م | 0.5ك.ب/تا max size -maximum density graciation 0 0 075…
6
Question // Date 1/1/2022 A company purchased equipment for 19,000,000 dinars and paid 3,000,000 dinars for transportation and installation expenses, and its useful useful life was estimated at 5 years, after which the value of the debris becomes 2,000,000. Required Prepare a table of depreciation and accumulated depreciation and extract the value of the equipment at the end of each year of its useful life using the sum of years' numbers method?