A compression-ignition engine with compression ratio of (1.50x10^1) is being designed. Pressure and temperature at the bottom dead centre are 1.3 bar and 400K. The engine operates according to the standard Diesel cycle. Assume polytrophic index to be (1.100x10^0). Compute pressure in bar at the top dead centre.

A compression-ignition engine with compression ratio of (1.50x10^1) is being designed. Pressure and temperature at the bottom dead centre are 1.3 bar and 400K. The engine operates according to the standard Diesel cycle. Assume polytrophic index to be (1.100x10^0). Compute pressure in bar at the top dead centre.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Manufacturing methods
Q3 Give the reason for 10 of the following. - 1- The use of lubricant in wire drawing die. 2- The uses of tungsten carbide for the manufacturing of die tool. 3- The increase of Mo/Si ratio during the production of white cast iron. 4- The addition of Al to copper alloys. 5- Aluminum is a better overall conductor than Copper for long distance electric transformation. 6- The addition of cryolite in smelting electrical furnace due to the production of aluminum. 7- The addition of Magnesium and Cerium during the production of Ductile cast iron. 8- The addition of 13% Cr to steel in corrosive environment. 9- The increase of hardness for chips due to the cutting process. 10- The brittle fracture of steel at low temperature lower than -4 C. 11- The heating of metal after the rolling process.
What is meant by Thicket and thinned? What is the difference in between both types? Note: Please do not handwritten and write short answer.
D. By using the following figure, suppose aluminum alloy and carbon steel have the same tensile properties, which metal will suggest to select working at low temperature? Why? fcc materials Low strength bcc materials High-strength materials Temperature Energy absorbed
Compare and contrast the differences between Paul Richer’s and Andrew Loomis’ concepts of proportions when drawing human characters. Explain your answer with some examples.
The rope you are uncoiling is a right hand lay rope, state with reasons the direction of uncoiling.
Q.B3. As part of a project, students have been asked to cast an Aluminium disc for use as a flywheel. The flywheel is part of an engine development project and needs to be 200 mm in diameter and 20 mm thick. Green sand casting will be used. The shrinkage associated with this metal and process is 5% at the solidification stage and further 3 % on cooling to room temperature. Aluminum has a density of 2710 kg/m³ and a melting temperature of 660°C. The pouring temperature is 700°C while the specific heat of aluminum is 887 J/kg.K. The latent heat of fusion of Aluminum is 396 kJ/kg. From previous experiments the Chorinov constant for the mold was found to be 10 s/mm². Determine: a.) The dimensions of the pattern (diameter and thickness) that will need to be made for this part (ignore riser and sprue). b.) The time it will take for complete solidification of the part. c.) Assuming an electric furnace at 10% efficiency is used to heat the metal and it takes around 2 hours achieve pouring…
In your own words, state and justify your assumptions and comment on your working.Marks will be assigned for the quality of the presentation of the working and od the comments.
Increasing the degree of graphite nodularity produces an improvement in cast iron elongation, due to ........... .........
Q1) One way of shaping raw materials into useful and valuable products is through casting process. Casting technology or process is one of the oldest processes in manufacturing field. During the last century, this casting process is used to create gold, jewellery and other products. (i) Draw TWO (2) casting processes that would be most suitable for making a gold and jewellery. (ii) Discuss your answer in (i) (iii) Explain why sand-casting process is not suitable for making a gold and jewellery.