A compound steel [G-82 GPa) shaft consists of solid 34-mm-diameter segments (1) and (3) and tube segment (2), which has an outside diameter of 56 mm and an inside diameter of 51 mm. Determine: (a) the maximum shear stress 7₂ in tube segment (2). (b) the angle of twist ₂ in tube segment (2). (c) the rotation angle Po/A of gear D relative to gear A. 0.3

A compound steel [G-82 GPa) shaft consists of solid 34-mm-diameter segments (1) and (3) and tube segment (2), which has an outside diameter of 56 mm and an inside diameter of 51 mm. Determine: (a) the maximum shear stress 7₂ in tube segment (2). (b) the angle of twist ₂ in tube segment (2). (c) the rotation angle Po/A of gear D relative to gear A. 0.3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Mechanics of Deformable Bodies Two forces are applied to the bracket BCD as shown. Knowing that the control rod AB is to be made of steel having an ultimate normal stress of 650 MPa, and the pin at C is to be made of steel having an ultimate shearing stress of 400 MPa, determine: (a.)The diameter of the rod for which the factor of safety with respect to failure will be 3.0. (b.)The diameter of the pin C for which the factor of safety with respect to shear will also be 3.0
SITUATION 31 Consider the system above. A rubber is used to bond a solid steel shaft (Diameter = 130mm) to another steel pipe (Diameter=200mm), fixed on the ground. A simple lever is used to test the bond between the two caused by the rubber. Bar AC has a length of 3m, a pin at B is used as the fulcrum of the system. Pin at B has allowable shearing stress of 100 MPa, the rubber has modulus of elasticity of 4.2 MPa and Poisson's ratio of 0.42. Consider deformation on rubber only, and pin at B experiencing double shear. 2000 100. A D-lémm 1. Determine the maximum vertical displacement of the shaft to not exceed the working shearing stress of the pin at B. 2. Considering Pin at B will not collapse. Determine the required force P to lift the shaft 5mm from the ground 225 00. 130
Q1: A torque T = 4 kN.m G of steel core 77 GPa and G of aluminum 27 GPa. Determine: (a) maximum shearing stress in the in the steel core. (b) the maximum shearing stress in the aluminum jacket. (c) the angle of twist at A. 172 mm 54 mm- A Steel core- 25 m Aluminum Q2: aluminum rod AB (G=27GPa) brass rod BD (G= 39GPa). portion CD of the brass rod is hollow and has an inner diameter of 40 mm, Determine: a) the angle of twist at A. b) maximum shear stress of rod AD c) torque diagram d) angle of twist diagram 60 mm TB 1600 Nm 36 mm T₁ = 800 Nm. 400 mm q+ 375 mm 250 mm
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.95 in., a length of L1 = 50 in., a shear modulus of 3800 ksi, and an allowable shear stress of 6.7 ksi. Brass segment (2) has an outside diameter of 0.85 in., a wall thickness of 0.13 in., a length of L2 = 38 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.0 ksi. Determine:(a) the allowable torque TB that can be applied to the compound shaft at flange B.(b) the magnitudes of the internal torques in segments (1) and (2).(c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB.
The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed connected at their ends. If there is no load in the members when T = 10 °C, determine the average normal stress in each member when T2 = 45 °C. Also, how far will the collar be displaced? The cross-sectional area of each member is 1130 mm?. B. -1 m - -0.6 m-
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.95 in., a length of L1 = 45 in., a shear modulus of 3800 ksi, and an allowable shear stress of 6.6 ksi. Brass segment (2) has an outside diameter of 0.80 in., a wall thickness of 0.14 in., a length of L2 = 32 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.2 ksi. Determine: (a) the allowable torque TB that can be applied to the compound shaft at flange B. (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB.
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.90 in., a length of L1 = 55 in., a shear modulus of 3800 ksi, and an allowable shear stress of 5.6 ksi. Brass segment (2) has an outside diameter of 0.75 in., a wall thickness of 0.06 in., a length of L2 = 20 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.4 ksi. Determine: (a) the allowable torque Tg that can be applied to the compound shaft at flange B (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque T.
F13-3. Determine the state of stress at point A on the cross section of the beam at section a-a. Show the results in a differential element at the point. 30KN 'as m'0.5m Но mm- 10 mm so mm 180 mm 10 mm- 10 mm Section aa
*R9 4. Two A36 steel pipes, cach having a cross-sectional area of 200 mm, are screwed together using a union at B as shown. Originally the assembly is adjusted so that no load is an the pipe. If the union is then tightened so that its screw, having a lead of 0.55 mm, undergoes two full turns, determine the average normal stress developed in the pipe. Assume that the union at B and couplings at A and C are rigid. Neglect the size of the union. Note: The lead would cause the pipe, when unloaded, to shorten 055 mm when the union is rotated ane revolution. -09m- a6 m.
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.55 in., a length of L₁ = 40 in., a shear modulus of 3800 ksi, and an allowable shear stress of 5.8 ksi. Brass segment (2) has an outside diameter of 0.45 in., a wall thickness of 0.15 in., a length of L₂ = 30 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.2 ksi. Determine: (a) the allowable torque Te that can be applied to the compound shaft at flange B. (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB. L₁ L2 TB (1) Answer: (a) TB= (b) T₁ = T2= (c) OB= B lb-ft lb-ft lb-ft rad (2) C
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.95 in., a length of L₁ = 40 in., a shear modulus of 3800 ksi, and an allowable shear stress of 6.0 ksi. Brass segment (2) has an outside diameter of 0.75 in., a wall thickness of 0.13 in., a length of L₂ = 28 in., a shear modulus of 6400 ksi, and an allowable shear stress of 7.7 ksi. Determine: (a) the allowable torque TB that can be applied to the compound shaft at flange B. (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB. y L₁ L2 TB. X (1) (2) N Answer: (a) TB = (b) T₁ = T₂= (c) DB = lb-ft lb-ft lb-ft rad B C
+ Asteel shaft (G =77 GPa) & an (Al) tube (G = 27 GPa) are connected to a fixed support & a rigid disk at the two ends. Knowing that the initial stresses are zero, determine the max torque that can be applied to the disk if the allowable stresses are ;.. = 120 MPa & 7, = 70 MPa for the steel shaft & (Al) tube respectively Rigid Disk Al Tube R e 76 mm I | Steel Shaft 50 mm B R | 8 mm 500 mm Trube ) Steel Shaft