A commercial venturi meter is placed in a vertical pipe as shown below. Pressure gauges are located at section 1 and section 2 and the pipe and throat diameters are as indicated. Assume that Cd=0.97 and calculate the downward discharge of water corresponding to pressures p1=65 kPa and p2=40 kPa.. Also, calculate the velocity at section 2. 20 cm 1 0.4 m 2 10 cm

A commercial venturi meter is placed in a vertical pipe as shown below. Pressure gauges are located at section 1 and section 2 and the pipe and throat diameters are as indicated. Assume that Cd=0.97 and calculate the downward discharge of water corresponding to pressures p1=65 kPa and p2=40 kPa.. Also, calculate the velocity at section 2. 20 cm 1 0.4 m 2 10 cm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At a certain flow range, for a system with certain geometric characteristics, in a pipe whose absolute roughness is 0mm, the pressure drop has a value of zero. True or False?
A differential manometer is attached to a pipe as shown. Calculate the pressure difference between points A and B
Answer fast will like
Explain each step please
4.5.4 The pressure at point 1 in the parallel pipe system shown in the figure below is 750 kPa. If the flow rate through the system is 0.50 m3/s, what is the pressure at point 2? Neglect minor losses. All the pipes are steel with roughness value of 0.046 mm. Also, determine the fraction of the flow in each of the parallel pipes and check your solution. Take the Kinematic viscosity, v = 1.141 x 10^6 m2 /s. 300 mm dia 1. 600 m, 240 mm dia A 450 m, 200 mm dia B C 720 m, 220 mm dia D 200 m, 300 mm dia 2.
Use g=32.2 */sec2 (9.81 m/s2) and 60°F (16°C) water unless told to do otherwise.• Google schedule-40 pipe’s thickness at different nominal size to obtain the innerdiameter of the pipe for accurate determinaLon of flow velocity.• Must show your work to support your selecLon. Otherwise, no points will be given.Water flows through a schedule-40 pipe that changes gradually in diameter from 6 in (154mm) at point A to 18 in (429 mm) at point B. The volumetric flow rate is 5.0 *3/sec (130 L/s). The respecLve pressures at points A and B are 10 psia (70 kPa) and 7 psia (48.3 kPa). All lossesare insignificant. What are the direcLon of flow and velocity at point A? (A) 3.2 */sec (1 m/s); from A to B(B) 25 */sec (7.0 m/s); from A to B(C) 3.2 */sec (1 m/s); from B to A(D) 25 */sec (7.5 m/s); from A to B
Reynold's number of 11090 is obtained for a certain value opening in a shut off valve experimentjexercise 1), when water flows through a pipe of diameter 23 mm. The viscosity of water is 1.14 x10-Nm Find the velocity of flow for this valve opening in m/s=
Find the reynolds number if a fluid of viscosity 0.4 Ns/m2 and relative density of 900 Kg/m3 through a 20 mm pipe with a Velocity of 2.5 m/s?
QUESTION 2 A venturi meter with a throat diameter of 100 mm is fitted in the inclined pipeline of 200 mm diameter with oil of specific gravity 0.88 flowing upwards. The venturi meter coefficient is 0.96. Two pressure gauges are fitted at tapping points, one at the throat reads the vacuum pressure of 40 cm of mercury and the other in the inlet pipe 320 mm below the throat is 20.231 N/cm2. If the loss of head in the main and throat is 0.35 times the kinetic head of the pipe, determine: 2.1 the volume flow rate of oil through the pipe 2.2 the difference in level in the two limbs of the mercury manometer if it is connected to the tapping points and connecting pipes are filled with the same oil
A pitot tube is inserted into an air flow to measure the flow speed to measure flow speed. The Pitot tube is inserted into a 100mm diameter tube so that it points upstream into the flow and the pressure as show in figure 5 where p0 = stagnation point. The static pressure is measured at the same location in the flow, using a U-tube differential manometer. Consider density of air equal to 2.3kg/m3 and determine the air flow rate.
A 200 mm long pipe slopes down at 1 in 100 and tapers from 0.25m diameter to 0.15 diameter at the lower end. If the pipe carries 100 litres of oil of specific gravity 0.85 find the pressure at the lower end. The upper end gauge reads 50 KPa.