A circular RCC water tank has an internal diameter of 10 m and has maximum height of water as 4 m. The thickness of wall is 160 mm and the walls of the tank are restrained at the base. IS-code coefficients for moment in cylindrical wall fixed to the base is given below. 2 Coefficient at point DT 0.8H 0.9H 1.0H 10 +0.0028 -0.0012 -0.0122 12 +0.0026 -0.0005 -0.0104 14 +0.0022 -0.0001 -0.0090 Take unit weight of water as 9810 N/m³ where, H = Height of tank, D = Diameter of tank, T Then moment at the base of wall using the given table is = Thickness of wall

A circular RCC water tank has an internal diameter of 10 m and has maximum height of water as 4 m. The thickness of wall is 160 mm and the walls of the tank are restrained at the base. IS-code coefficients for moment in cylindrical wall fixed to the base is given below. 2 Coefficient at point DT 0.8H 0.9H 1.0H 10 +0.0028 -0.0012 -0.0122 12 +0.0026 -0.0005 -0.0104 14 +0.0022 -0.0001 -0.0090 Take unit weight of water as 9810 N/m³ where, H = Height of tank, D = Diameter of tank, T Then moment at the base of wall using the given table is = Thickness of wall

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

56 mm T = 26 mm 7m As the hollow steel shaft shown rotates at 240 rpm, a stroboscopic measurement indicates that the angle of twist of the shaft is 5°. Knowing that G = 77.3 GPa, determine (a) the power being transmitted, P = kW (b) the maximum shearing stress in the shaft. Tmax MPa
8. A cast iron pipe of external diameter 40 mm, of internal diameter 20mm and of length 4 meter when the pipe is supported at its ends and carries a point load of 80N at its centre. I. Calculate the maximum bending moment apply in the beam cross section. П. Calculate the maximum bending stress. 40 mm- 80 N 20 mm- 4 m (a) (b) Area of cross-section
Н.W. 7] The unstretched length of spring AB is 3 m. If the block is held in the equilibrium position shown, determine the mass of the block at D. 3 m- 4 m kẠC = 20 N/m www www kAB = 30 N/m %3D 3 m %3D kAD = 40 N/m De
A reinforced concrete beam has a width of 400mm and an effective depth of 600mm. It is reinforced for tension with 4-28mm rebars. F'c = 20.7MP and Fy = 414.6MPa. 7. Determine the ultimate moment capacity. a 484.76KN.m b. 448.67KN.m 8. Determine the percent increase in ultimate b. 34.4% a. 25.1% c. 487.46KN.m d. 446.87KN.m moment if depth is increase to 700mm. c. 18.98% 15.68%
• Problem 14.1. Determine elastic curve of the solid circular shaft. The shaft is made of steel having E = 200 GPa. It has a diameter of 100 mm. M-30kN m 1.5 m 1.5m- R-10KN R3 -10KV
A pipe with a weight of 3.7 kg/m is attached to a wall such that all degrees of freedom are restraint. At the free end of the pipe a vertical load P=100 N pointing downwards is introduced with an excentricity of 100mm from the axis. The pipe has an length of 1m and is made of steel with the Young's modulus of 210 GPa and the Poisson ratio of 0.3125. The moment of inertia is l=19.7 cm“ whereas the polar moment of inertia J = 2 I. First, as part of the mechanical properties determine the Shear Modulus. Then determine the total vertical deflection at the point where the vertical load is being introduced. Note: Use the principal of superposition. ANSWERS: Shear Modulus %3D [MPa] Vertical deflection due to weight only [mm] Vertical deflection due to End-Load (excentricity NOT considered) [mm] Vertical deflection due to excentricity of the End-Load only [mm] Total vertical deflection [mm]
The air above the liquid is under a pressure of 40 kPa gage, and specificgravity of the liquid in the tank is 0.80. The rectangular gate is 2.0 mwide, y1 = 1.0 m and y2 = 3 m. 1. Determine the hydrostatic force acting on the gate, in kN 2. What is the location of the force, in m, measured from the hinge? 3. Calculate the minimum value of P, in kN, to hold the gate in place
Very very Urgent The distributed load q and the singular moment M act on the stepped shaft given in the figure. Draw the cross-sectional influence diagrams of the system under these forces. Determine the maximum stress value for the critical section. L1 = 226 mm ,L2 = 118 mm, a = 159 mm M = 572 N.m, q = 5 N/mm D = 51 mm , d1 = 19mm , d2 = 5 mm
Problem # 1: A hollow shaft has an outside diameter 60 mm and a wall thickness of 1.25 mm. The maximum shear stress in the shaft must be limited to 150 MPa. Use G = 43 000 MPa. Determine: (a) the maximum power that can be transmitted by the shaft if the rotation speed must be limited to 20 Hz. (b) the magnitude of the angle of twist in a 700-mm length of the shaft when 30 kW is being transmitted at 8 rpm.
The beam shown is hinged at one end, It is supported by two steel rods of equal length of 1.5m. Before the load is applied, the beam hangs level. Use E = 200, 000MPa and a = 11.7. Neglect bending of the beam. m°C FT A=640mm? A=320mm2 B C D 1.2 m 0.8 m 12m V 54KN 1. Axial load at steel rod in kN? un 2. Axial stress at steel rod in MPa? 3. Axial deformation of aluminum rod in mm? 4. Axial deformation of steel rod in mm? 5. Axial Load at aluminum rod in kN?
Q2. Determine all forces acting on body A for the system shown in figure 2. Body A weighs 200 N and the cylinder B weighs 500 N. assume all the contact surfaces are smooth. 24 ring Cable 7 A r= 0.5 m 30 0.5 m B 2 m 1m 1 m 30°
A simply supported beam is subjected to a linearly varying distributed load q(x) = 9, with maximum intensity qo at B. The beam has a length L = 4 m and rectangular cross section with a width of 225 mm and height of 270 mm. 90 q(x) В -L- Determine the maximum permissible value for the maximum intensity, 9o. (in kN/m) if the allowable normal stresses in tension and compression are 131 MPa. kN/m