(b)A channel has to be designed for drainage to carry flow from 200 km. If theflow/km' is 0.5 m'/sec/ km, determine the Trapezoidal Channel section using (i) thepermissible velocity method, (ii) the regime theory. The material size is 2 mm and So= 0.00002. Assuming other data, if missing.Comment also on your design outcomes based on two methods.

Answered: Image /qna-images/answer/aa3bda0f-db4a-4112-9130-cf9579659308.jpg

Answered: A channel has to be designed for…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A series of pipes with Q=194 L/s was to be examined for head losses. If the roughness coefficient is 0.012, what is the minimum diameter (mm) of the pipe that could replace all three in that series? Use Manning's approach. Length (m) Pipe Pipe 1 Diameter (m) 0.43 1,706 1,547 Pipe 2 0.34 Pipe 3 0.29 839
Consider a watershed with a drainage area of 10 square miles and a mainstream length of 7.5 miles. The main channel extends from the watershed outlet to the point opposite the centre of gravity of the watershed over a distance of 3.5 miles. Given a time of concentration (Ct) of 1.5 hours and a dimensionless slope of the watershed (Cp) of 0.5, determine the standard synthetic unit hydrograph for this basin. What is the duration? Using Snyder’s method, calculate the 45-minute unit hydrograph parameter
Read the question carefully and give me answer according to the question
It is proposed to design a rectangular channel in Dera Ismail Khan where silt factor is 1.25 for irrigation purposes. The served area is such that a discharge of (your ID divided by 100) cumecs is enough. Using Lacey's Theory, design a regime channel. You need to find out the depth of the channel, width of the channel and bed slope of the channel
1. Measurements in a trapezoidal channel yield a flow rate of 100 m³/s, a flow depth of 3 m, a bottom width of 3 m, side slopes of 3:1 (H:V), and a longitudinal slope of 0.5%. The channel is observed to be lined with gravel-sized stones that are estimated to have a specific weight of 25 900 N/m³ and an angle of repose of 37°. (a) Calculate the median size of the stones on the perimeter of the channel. (b) Using the calculated stone size, determine whether you expect the channel to be stable in its current configuration. Assume a safety factor of 1, and neglect the effect of the longitudinal slope on the permissible shear stress. [For water, take 7 = 9789 N/m³, v = 1.00 x 10-6 m²/s]
Please solve and explain
/A stable canal is to be designed for a discharge of 30 m3/sec with average size of the bed material is 0.3 mm. Calculate the canal dimensions. What would be the dimensions of this canal if it were to be designed on the basis of Kennedy,s method with critical velocity ratio equal to unity, Bazin,s coefficient of 1.3 and the ratio of bed width to depth of flow the same as obtained above. 4
You were assigned to describe the pore water pressure in Figure 1. It shows the cross-sectionof a homogenous compacted earth dam highlighting the flow behavior. Excessive rainfall hassaturated the embankment. Given the three points A, B and C. A. Which of the points will have the highest positive pore water pressure?B. Which of the points will have the lowest positive pore water pressure?
A 5.5 m diameter circular concrete culvert has a drainage water flowing at a height of 4.6 m. Compute for the hydraulic radius (in m). Answer in TWO(2) decimal places. Numerical values only. Don't indicate units here, just on the submitted solution.
The peak discharge for a circular culvert was found to be 1.25 m^3/s. It has been determined that a water flow speed of 1.5 m/s is needed to maintain scour velocity. Calculate the approximate diameter of a circular culvert needed to carry the 1.25 m^3/s if the culvert is flowing at a depth 3/4 of the diameter. Assume that the flow in the culvert is not complex and water does not pond at either end of the culvert.
We are designing a culvert and a project criterion is to not have roadway overtopping. We need to calculate the TW, HW elevation, and maximum allowable total head loss (H) as a step in the design process of the culvert. What are the values of TW, and H using the information in the table below: Parameter Normal depth (d): Upstream invert or flow-line elevation: Length of culvert: Slope of culvert: Maximum HW elevation: value 5 ft 75ft 50 ft 0.002 85 ft
Answer in two decimal places please

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS