A certain microphone is capable of delivering 0.5 V when someone claps their hands at a distance of 10 ft. A particular electronic switch has a Thevenin’s equivalent resistance of 620 Ohms and requires 100 mA to energize. Using Op-Amp, design a circuit that will connect the microphone to the electronic switch in such a way that the switch is activated by someone clapping their hands

A certain microphone is capable of delivering 0.5 V when someone claps their hands at a distance of 10 ft. A particular electronic switch has a Thevenin’s equivalent resistance of 620 Ohms and requires 100 mA to energize. Using Op-Amp, design a circuit that will connect the microphone to the electronic switch in such a way that the switch is activated by someone clapping their hands

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter5: Components, Symbols, And Circuitry Of Air-conditioning Wiring Diagrams

Section: Chapter Questions

Problem 16RQ: Which of the following is not a requirement for an electric circuit? a. a source b. a path c. a load...

See similar textbooks

Similar questions

What is the unit of measurement for the strength of a capacitor? microamp microtorque microfarad microwatt
A platinum resistance coil is to be used as a temperature sensor and has an initial resistance of 200 ohms .It forms one arm of a Wheatstone bridge with the bridge being balanced at this temperature and each of the other arms also being 200.If the temperature coefficient of resistance of platinum is 0.0045 , what will be the output voltage from the bridge for every 5 degree changes in temperature if the supply voltage is 15.0 V? a.0.16V b.0.159V c.0.16875 V d.0.17V
Explain the operation of the opamp circuit in the figure. In what situations does the LED illuminate; which cases remain dim? What is the type (function) of the circuit? +12V 10K V. 10K 470 A v O -12V LED
The output of a LVDT is connected to 10 V voltmeter through an amplifier of amplification factor 515. The voltmeter scale has 174 divisions and the scale can be read to 1/3th of a division. An output of 6.6 mV appears across the terminals of the LVDT when the core is displaced through a distance of 2.6 cm. Calculate (a) the sensitivity of the LVDT, (b) sensitivity of the whole setup and (c) the resolution of the instrument in cm
A thyristor of a latching current 100 mA is connected in series with the resistor (R). The input voltage vi=20sinwt V. The maximum R for switching on the thyristor at a firing angle of 30 degrees is:
Consider a PV Module with 4 solar PV cells with the Size of each 10cm x 10cm are connected in Parallel. If we connect a lamp load of 2W across this module, choose the correct statement for the above PV Module. (Assume necessary data) a. The output voltage is 0.5V, the output current is 2A b. The output voltage is 0.5V, the output current is 4A c. The output voltage is 2V, the output current is 2A d. The output voltage is 2V, the output current is 4A
Calculate the dc and ac components of the output signal across load RL in the circuit of Figure * V- 150 V v, (ms) = 15 V v, (ms) 500 2 Full-wave rectifier R 5 ka 15uF 10μF
For the differentiator op-amp circuit in Figure 5: a) If the sine wave input is V1= 0.02 sin 300x10³t what is the output voltage, v. when t= 10 ms. b) Draw the input and output waveforms. 200 ko 0.1 μΕ V1. OP Vo AMP Figure 5
V1 R1 V2 Da Db R2 www V3 Given that R1=2k, R2=1k, and Da and Db are Si Diodes: a. What is V3 in terms of V1 when Da is ON? b. What is V3 in terms of V1 when Db is ON? c. What is V3 in terms of V1 when Da and Db is OFF?
How fast can the output of an Op-amp change by 10 V, if Its slew rate is 1 V/μs ?
find zener voltage and resistance with given values:capacitor: 470 micro Fresistor: 12 ohmV out: 12V DCI out: 1AV in: 120V AC 60 Hzdiode: 0.7V
Household circuits are often wired with two different widths of wires: 12-gauge and 14-gauge. The 12-gauge wire has a diameter of 1/12 inch while the 14-gauge wire has a diameter of 1/14 inch. Thus, 12-gauge wire has a wider cross section than 14-gauge wire. A 20-Amp circuit used for wall receptacles should be wired using 12-gauge wire and a 15-Amp circuit used for lighting and fan circuits should be wired using 14-gauge wire. Based on the information stated in the above question, explain the risk involved in using 14-gauge wire in a circuit that will be used to power a 16-ampere power saw. (can you please answer no. 1 THANK YOU!)