Example 1A cart is pulled uniformly along two cables using two horsesas shown below, the tension forces along the two cables1100 N and the angle betweenare P900 N and Qthem are a60°.Determine the magnitude of the resultant force (R)and theangles between the resultant and the two tension forces.Q = 1100Na = 60°R =?CartP = 900N

Answered: Image /qna-images/answer/33eb4b21-37b4-40cc-b818-9346c2342bca.jpg

A cart is pulled uniformly along two cables using two horses as shown below, the tension forces along the two cables 1100 N and the angle between 900 N and Q them are a = 60°. are P %3D %3D Determine the magnitude of the resultant force (R)and the angles between the resultant and the two tension forces. Q = 1100N a = 60° R =? Cart P = 900N

A cart is pulled uniformly along two cables using two horses as shown below, the tension forces along the two cables 1100 N and the angle between 900 N and Q them are a = 60°. are P %3D %3D Determine the magnitude of the resultant force (R)and the angles between the resultant and the two tension forces. Q = 1100N a = 60° R =? Cart P = 900N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If you are 100 % confident then you can solve it otherwise leave it. I want right solution
Problem Determine the value of Ely midway between the supports for the beam loaded as shown in Fig.. El y = 0950 N-m³ answer M = 1800 Nm 2m R₂ 2 m 200 N/m 2 m R₂ 2 m
Please answer attached image.thank you
For questions 1 to 5, consider a bent rod fixed at the wall at A and is acted upon by a 20- N force (parallel to the z-axis) and a 50-N force (parallel to the y-axis) applied at points B and C, respectively. y Z A Rx, Mx Ry, Mx, My, Mz Rx, Ry, Rz, My, Mz Rx, Ry, Rz, Mx, My, Mz -4 m- C -2 m- 50 N 20 N. x B X 5. Which of the following are the reactions at the support at A? R are force reactions and M are moment reactions.
A solid green bar with d= 57mm is placed inside a hollow blue bar with external diameter D=127mm if they carry torque t= 142Kn m and the length L=5m what is the ratio of the torque of the solid hollow bar. Gsolid=170Gpa and Ghollow= 200gpa
1) Consider the column below. If both sections are made of a steel with the Modulus of Elasticity of 200 GPA, calculate the stresses in both sections and the movements (displacements) of B and C. (Learning Activity: L06) 1 m 4 m 1.5 MN B 2 MN 1.5 MN 30 cm Cross Sectional Area BC: Hollow Circle with 2 cm thickness 60 cm Cross Sectional Area AB: Hollow Rectangle with 1 cm thickness 30 cm
Find the Force in EG shown in the figure.
Using the Portal Method determine all the member forcesof the frame shown below. Submit your answers in the format where the member forces are written along the corresponding members as illustrated in the short video discussion. Computation of such values may no longer be shown. a= 7 m b= 10 m P= 116 kN ЗР/2 G H 4m P 5m a b
Review Problem 4.8 Take that L = 13 ft. (Figure 1) Figure 1 of 1 L 800 lb/ft L > B Part A Replace the distributed loading by an equivalent resultant force. Express your answer to three significant figures and include the appropriate units. FR = Submit x = Submit Value kip μÀ Part B Specify the location of FR on the beam, measured from the pin at C. Express your answer to three significant figures and include the appropriate units. 0 μᾶ Value My Answers Give Up ft My Answers Give Up ? ? Provide Feedback Continue
The simply supported beam AB shown in the diagram has a length L=8 m and subjected to a uniformly distributed load q = 4 kN/m, a point load P = 16 kN located at a distance a = 0.3*L m from support A and a moment M = 14 kN.m located at distance d=0.8*L m from support A. What is the value of the bending moment under the point load P. Give your answer to one decimal place. M d
2. A uniform rectangular block is attached to a cart that is accelerating up a 20° incline at 3 m/s². The block is attached to a cart by a hinge at Point A and a roller at Point B. a. What is the force that the roller is applying to the block at Point B? b. What is the force that the hinge is applying to the block at Point A? Y a = 3 m/s² х 20° 0.8 m m= 100 kg B 0.6 m 1.0 m g
1) will upvote anyone who will answer