A car is travelling 50mi/hr on a good, wet, level road. The car weighs 3200 lIbs, has Cp=0.35, A=20ft, and a gear reduction ratio of 5 to1. The air density is 0.002045 slugs/ft° and the car is producing 150 ft.lb of torque, with a wheel radius of 14 inches, and a mechanical efficiency of the drive train is 80%. The wheelbase is 100 inches, the center of gravity is 20 inches above the road surface and 50 inches behind the front axle. What is the acceleration if the car is front wheel drive?

A car is travelling 50mi/hr on a good, wet, level road. The car weighs 3200 lIbs, has Cp=0.35, A=20ft, and a gear reduction ratio of 5 to1. The air density is 0.002045 slugs/ft° and the car is producing 150 ft.lb of torque, with a wheel radius of 14 inches, and a mechanical efficiency of the drive train is 80%. The wheelbase is 100 inches, the center of gravity is 20 inches above the road surface and 50 inches behind the front axle. What is the acceleration if the car is front wheel drive?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

pls help! Write the complete solutions and legibly. Answer in 2 decimal places. UPVOTE WILL BE GIVEN! MECHANICS OF DEFORMABLE BODIES Let Q = 0 and T = 6 (Example: 4QT mm2 = 406 mm2). Just substitute the number in letter. Thank you! A rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the figure. The cross-sectional area of each bar is 4QT mm2. Determine the average axial stress in each bar.
Please explain the derivative part better, it makes no sense to me on how the 2 came to be
4.1 PLEASE!!! provide complete step by step solutions with at least three parts of the given drawing and an FBD. *please follow my instructions this is very important to me. thank you very much!
I need answer within 20 minutes please please with my best wishes
A circular plate of radius r= 0.863 m is adjacent to a rectangular plate with base b = 0.944 m and height h = 0.718 m which lies next to a triangular, isosceles plate with base b = 1.509 m and height h = 0.7980 m. t t r r The plates lie on a common baseline and the origin is in the lower left corner, see figure. AY r br h₂ b₁ ht X Determine the centroid of the rectangular plate in the x-direction if its surface density varies in the x-direction according to o r 2 = = 4,55.x kg/m .
Given data : Work done=20 Joule Displacement=5 m Calcualte force applied
dy/dx + y = e^x solution is y = e^x/2 + Ce^-x prove it
Write a conclusion about the image
Determine all bar forces in the truss shown below. Construct a table summarizing your answers. Limit all final answers to three decimal places.
Please help me understand this. If you can also provide understandable formula that would be nicer. Thank you ^^
pls help! Write the complete solutions and legibly. Answer in 2 decimal places. UPVOTE WILL BE GIVEN! MECHANICS OF DEFORMABLE BODIES Let Q = 0 and T = 6 (Example: 4QT mm2 = 406 mm2). Just substitute the number in letter. Thank you! A rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the figure. The cross-sectional area of each bar is 4QT mm2. Determine the average axial stress in each bar.
A block of wood 0.25 m thick is floating in sea water. The Specific Gravity (SGw) of Wood is 0.35 while that of sea water (SGs) is 1.02. Summarize your answer like the format below and Find the minimum AREA of a block that will support a man weighing 80 kg. (Clue: - m^2) 大, Wman = 80 kg Wwooo BF Weight of the man Unit weight of the wood N m Unit weight of sea water Equation of Volume of Wood Block N m Area of the block m? zlzzE