A cantilever timber beam with a span of L- 3.7 m supports a uniformly distributed load w. The beam width is b- 320 mm and the beam height is h- 270 mm. The allowable bending stress of the wood is 5.7 MPa. Determine the magnitude of the maximum load w that may be carried by the beam. Answer: w kN/m. Save for Later Attempts: 0 of 1 used Submit Answer

A cantilever timber beam with a span of L- 3.7 m supports a uniformly distributed load w. The beam width is b- 320 mm and the beam height is h- 270 mm. The allowable bending stress of the wood is 5.7 MPa. Determine the magnitude of the maximum load w that may be carried by the beam. Answer: w kN/m. Save for Later Attempts: 0 of 1 used Submit Answer

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A TIMBER BLOCK "B x B" mm SQUARE IS REINFORCED ON OPPOSITE SIDES BY A "B" mm AND 't' mm THICK STEEL PLATES. DETERMINE THE THICKNESS 't' SO THAT THE ASSEMBLY WILL SUPPORT AN AXIAL LOAD OF 1000 KN WITHOUT EXCEEDING A MAXIMUM TIMBER STRESS OF 12 MPa OR A MAXIMUM STRESS IN STEEL OF 350 MPa. MODULUS OF ELASTICITY OF STEEL AND TIMBER ARE 210 GPa & 7 GPa RESPECTIVELY. B t B t PROB 04
Flexure beam.
Answer problem1
Topic: Restrained Beams 140KN 2.5m 3.5m 5KN/m 3.2m МА 6m MB 11WL2 Pab² 5WL2 Pa?b MA = - MB = - 192 L2 192 L2 INSTRUCTION: 1. Determine the maximum stress in the timber beam with the size of 120 x 370mm.
Problem: Using WSD & USD, design the midspan reinforcement of stringer (B-3) for the second floor of a 3-storey residential building shown below. Use 20.7MPa compressive strength of concrete @ 28-days and grade 40 reinforcing bars. Use Ye= 24.5 KN/m³. Design the stringer as rectangular beam. Assume simply supported. 450mm 250mm 250mm 450mm, Superimposed Deadloads = 2.70 KPa Stirrups = 10mmo Main bar = 25mm 350mm B-4 STAIRWELL B-1 250x400mm S-3 B-3 250x400mm S-4 (3000) mm 350mm B-4 350mml Stringer Section (2000) mm (3500) mm (2000) mm 700mm
A TIMBER BLOCK “B x B” mm SQUARE IS REINFORCED ON OPPOSITE SIDES BY A “B” mm AND ‘t’ mm THICK STEEL PLATES. DETERMINE THE THICKNESS ‘t’ SO THAT THE ASSEMBLY WILL SUPPORT AN AXIAL LOAD OF 1000 KN WITHOUT EXCEEDING A MAXIMUM TIMBER STRESS OF 12 MPa OR A MAXIMUM STRESS IN STEEL OF 350 MPa. MODULUS OF ELASTICITY OF STEEL AND TIMBER ARE 210 GPa & 7 GPa RESPECTIVELY.
A laminated beam is composed of four (4) planks, each of 150 mm x 30 mm, glued together to form a section 150 mm x 150 mm. The allowable shear stress in the glue is 850 kPa, the allowable shear stress in the wood is 1050 KPA, and the allowable flexure stress in the wood is 10 MPa. Determine the maximum uniformly distributed load which can be carried by the beam on a 45 m simple span.
A timber beam 150 mm wide and 200 mm deep is to be reinforced by bolting on two flitched each 150 mm x 12.5 mm in section. Find the moment of resistance when the flitched are attached symmetrically at the top and bottom. Allowable stress in timber is 6 N/mm². (Es= 20 Ew)
using the table below, answer the question
Only correct answer with solution
A 300mm x 425 rectangular beam is reinforced for tension only with 4-28mm bars. The beam has a concrete cover of 40mm and a stirrup of 10mm diameter bar. The beam carries a live load and a dead load (without its self-weight). Given that unit weight of concrete is 24kN/ cu.m f'c = 21 MPa and fy = 414 MPa, calculate the additional concentrated live load as shown in the figure.
(a) Draw the shear and bending-moment diagrams for the beam and loading shown below. 48 kips 48 kips 48 kips B A E -6 ft- 2 ft' 2 ft 2 ft (b)If the cross-section of the beam is as shown below, determine the maximum tensile and compressive stresses. 8 in. 1 in. 1 in.- 6 in. 1 in. 4 in.