%DA cantilever beam has a cross-section and concentrated loads P1 = 30 kN andP2 = 10 kN, as shown.Write all answers in 2-decimal places.35 mm 250 mmP1P235 mmB500 mm1.8 m3.2 m Compute for the maximum tensile bending stress (in MPa).Your answerCompute for the maximum compressive bending stress (in MPa).Your answerCompute for the bending stress (in MPa) 2 m to the right of point A and 30mm from the top of the beam. *Your answerFind the maximum shear stress (in MPa) for the beam and cross-section. *3.

Answered: Image /qna-images/answer/b490544e-ee84-42c7-a94c-14319cd8b338.jpg

Answered: A cantilever beam has a cross-section…

A cantilever beam has a cross-section and concentrated loads P1 = 30 kN and P2 = 10 kN, as shown. Write all answers in 2-decimal places. 35 mm 250 mm P2 35 mm B 500 mm A 1.8 m 3.2 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The frame shown is fitted with three 53 cm diameter frictionless pulleys. A force of F = 635 N is…

A: Data given Diameter of pulley = 53 mm F =635 N Find: (a) At point A, Force at A (b) Reaction…

Q: ! Required information Consider the loading condition shown. Assume that the flexural rigidity El of…

A: Since the Deflection at point B is given and is correct so ; Deflection at B = 0.0013 wL4EI The…

Q: Problems: Analyze the rigid frame given below using either the Portal Method or the Cantilever…

Q: 1268 N D 418 N 1.5m F A E 1.5m 3m 1.5m B

Q: The beam is fabricated from two equivalent structural tees and two plates. Each plate has a height…

A: Given :

Q: Instruction: Solve the following problems. Show your brief solution. Kindly box your final answer.…

Q: Question 4 Determine the bending moment 5.52 ft to the right of point A for the beam shown belowif P…

A: Given data in question UDL Point load Concentrated moment Span member length To find out Moment

Q: should be set initially, find the maximum load F? The cross

Q: Let, P=70KN, a=2.5m, b=1.5m and c=4m ; Also, DON'T FORGET TO TYPE DOWN THE CORRECT UNITS (IF NEEDED)…

A: P =70KN L = 9.5m

Q: 12. The concrete table column-support in Problem 20is reinforced with three -in steel rods, as shown…

Q: A B L P D L L Calculate the deflection at A (the end opposite of the load) and at D (under the…

A: Given Data Find the deflection at A and D.

Q: Note: Please show all of the free body diagrams used and also show the complete solution. The beam…

A: Deflection will be determined by the first mentioned method i.e. double integration.For other…

Q: A double tee cross section is used for the beam shown below. Assume the following lengths and loads:…

A: Given:a = 14 ft, b= 7ft, c= 9ftP= 8000lb, Q = 3000lbMoment of inertia= 110 inch4Required:Maximum…

Q: ) Determine Ma using method I in which the T-section is divided into two parts, i.e., overhanging…

Q: n shown below, determine the number of 16mm diameter bars Fored

Q: 9. What will be the slope at point B? 10. What value of load P is needed in order to produce a zero…

A: Given P = 250 kNs = 2mW =-7x +81E = 200 GPaI = 2*109 mm4.It is asked to determine the following,1.…

Q: -51.476603223441mm, Determine the radius of the cross-section of the circular beam. Determine the…

A: E = 90 GPaMaximum shear force = 508.4 kNP = 190 kNa = 2 mb = 1 mc = 3m Calculations for support…

Q: EX3: For the beam shown in the figure below. Find maximum allowable ve load(P)that the beam can…

Q: The force F = 45O Ibs acts on the frame. Resolve this force into components acting along members AB…

A: From the given information we have to calculate the reaction at the member AB and AC

Q: Compute the safe uniformly distributed dead load that will be added to the weight of the beam. The…

A: We have yconc =2 4KN/m3. b = 280mm d = 415 mm fc' = 25MPa fy = 420MPa As = 6-20mm diameter bar…

Q: Deflection Given: the beam cross-section shown have the following cross-sectional properties f'c…

A: Gross moment of inertia(Ig)Critical internal moment(Mcr)Maximum service load(Ma)Critical moment of…

Q: By DIM & MAM, determine the value of EIẟ at midspan for the beam loaded as shown.

Q: STRENGTH OF MATERIALS UPVOTE WILL BE GIVEN. Please write the complete solutions legibly. Answer in 3…

A: Given values: Fy = 350MPa Fu=450 MPa Es=200,000 MPa Consider the loaded beam.

Q: Note: Please show all of the free body diagrams used (from reactions and etc.,) and also show the…

A: Deflection will be determined by the first mentioned method i.e. double integration.For other…

Q: For the given properties of the beam below, determine the safest wu that the beam will carry. bf =…

Q: e) What is the maximum magnitude of shear force and bending moment, neglecting the sign? Maximum…

A: Given simply supported wooden beam,Uniformly Distributed load, w = 6 N/mmThe cross- section of the…

Q: 1- Calculate maximum deflection of the beams. 2- Check the suitability of the section assuming the…

A: UKB 457 x 152 x 82 I = 366,000,000 mm4 E = 2 x 105 FIND1- Calculate maximum deflection of the…

Q: Please answe

Q: A piece of wood was cut into 3 pieces as shown below and will form into a l-beam section. Planks 1…

Q: For the beam shown in the figure below, find the maximum tensile and compressive flexural stresses.…

A: step 1-

Q: Determine the bending moment 7.59 ft to the right of point B for the beam shown belowif P = 505 lb,…

A: Given data in question Load Span member length To find out Moment at 7.59ft right of point B

Q: Calculate the stiffness of the I-beam with respect to the y-axis when h = 190, b = 100, t1 = 9 and…

A: Given: h = 190 b = 100, t1 = 9 and t2 = 6 mmRequired: stiffness of the I-beam with respect to the…

Q: 2.1. Determine the magnitude of the resultant force acting on the screw eye and its direction…

A: Resultant force is generated due to action of two or more force acting on the body.For determining…

Q: Need help asap pls. The beam is shown below. The cross-section of the beam is 250 mm x 400 mm. Take…

A: Given Data E = 200 GPA Cross section of beam 250 mm × 400mm Find 1. Deflection at right end of…

Q: The continuous beam shown below has an internal hinge at point C. The beam is loaded with two…

A: To determine:1) the vertical deflection at C2) the vertical deflection at F3) the rotation at A4)…

Q: A 10 kN ww E G BD F H K 8 @ 2m = 16 m L 5 kN www 15 KN O M N P 4.0m

Q: The beam is subjected to a shear of V = 34 kN. Set 300 mm Part A 20 mm A 20 mm Determine the web's…

A: Given: The shear force in the beam is 34 kN. Consider the figure.

Q: conjugate beam me thod Please use

A: CONJUGATE BEAM METHOD Given, E = 200GPa I = 240*10^6 mm^4

Q: 2. The concrete table column-support in Problem 20is reinforced with three -in steel rods, as shown…

Q: Given a 9.8 m column pinned at the top and fixed at the bottom with the following properties: Fy =…

Q: The beam supports the loads as shown in the figure. Using E = 200 GPa, w = 16KN/m, P= 16KN and M=…

Q: Kindly write complete and clear solutions

Q: Determine the design moment capacity Mn of the beam shown in the figure if b1=160 mm, b=76 mm, a=78…

A: Φbar = 34 mmfc = 31 MPafy 413 MPa

Q: Step 2: Calculate the area of design steel: • Let's assume the given beam section is a balanced…

Q: A flanged wooden shape is used to support the loads shown on the beam. The dimensions of the shape…

A: Answer We can calculate Maximum Tensile and Compressive Bending stress using Bending equation σ =…

Concept explainers

Material Properties

Construction in civil engineering demands high strength, durability, and longevity. These targets can be achieved by better design and analysis, along with the correct choice of materials. Different materials have different properties and hence, they respond and performs differently under the various condition of external loadings. It is therefore a critical task of an engineer to select the right material based on the property that the material is supposed to function in real-time. When speaking about the property, there are different categories of material properties like chemical property, physical property, mechanical property, electrical property, magnetic property, thermal property, etc. These material properties form the basis of material selection in various applications.

Question

%D
A cantilever beam has a cross-section and concentrated loads P1 = 30 kN and
P2 = 10 kN, as shown.
Write all answers in 2-decimal places.
35 mm 250 mm
P1
P2
35 mm
B
500 mm
1.8 m
3.2 m

Compute for the maximum tensile bending stress (in MPa).
Your answer
Compute for the maximum compressive bending stress (in MPa).
Your answer
Compute for the bending stress (in MPa) 2 m to the right of point A and 30
mm from the top of the beam. *
Your answer
Find the maximum shear stress (in MPa) for the beam and cross-section. *
3.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

#2 will upvote anyone who will answer correctly. Correct decimal places please. Thanks
i need the answer quickly
Express your intermediate answers with FRACTION and simplify your FINAL answers up to TWO DECIMAL PLACES.BOX your FINAL ANSWERS
Part A The W14 x 30 cantilever beam is made of A-36 steel and is subjected to the loading shown in (Figure 1). Assume w = 3.5 kip/ft. Determine the slope at the end B of the beam, measured clockwise. Express your answer in radians to three significant figures. Figure W > Өв = 跖 ΕΠΙ ΑΣΦ 个 vec Submit Request Answer Part B 1 of 1 > 0 ? rad Review Determine the displacement at the end B of the beam. Express your answer in inches to three significant figures. Enter positive value if the displacement is upward and negative value if the displacement is downward. 30 kip-ft VB = A B 6 f -6 ft A 跖 ΜΕ ΑΣΦ IT vec Submit Request Answer Provide Feedback ? in. Next>
Help me figure out the problem. Asking for the moment diagram? and then, Show the value of x knowing you have the shear diagram. Again find the moment diagram and the value of your x. Show complete solution and box the final answer and write on a paper.
Solve the given problem. Round off answers in all computations in 4 decimal places. Determine the moment capacity of the beam shown in the figure.
Find the value q can take so that the BD bar, the cross section of which is shown in the figure, can carry the given load without buckling. factor of safety n = 3 Ri= 7cm , Rd=9cm on BD bar
SHOW COMPLETE FBD
PLS ANSWER ASAP. PROVIDE COMPUTATION THANKS!
1. A simply supported beam carries three concentrated loads as shown in the figure. a. Determine the slope and deflection equation for every segment of the beam. b. Determine the deflection per El at the right half of the beam. (hint: Eq. - Ely = 54x-2/3x³-5/3[x-67³-6264) c. Determine the value of Ely under the 8-kip load. (Ans: 6246 kip.ft³) 10 kips 8 kips 6 ft 6 ft 6 ft 10 kips 6 ft
A 3 m long beam has a 4 kN/m distributed load applied to the cantilever steel beam as shown below. The dimensions for a = 40,b= 40, c = 40, and d = 100. a w kN/m >a d Section a-a (unit in mm) Mc M 1_M FORMULAS: 06 = or == " I S P EI L b C
Topic: BEAM BEARING PLATES AND COLUMN BASE PLATES Please solve your Solution in a handwritten Note: It should be handwritten pleaseeee A bearing plate is used to support a W 21 x 68 beam having a spam of 6m which carries a uniformly distributed loads as follows:DL including its own weight: 60 kN/mProperties of W21x68 d=537mmbf=210mmtf=17.40mmtw=10.92mmk =36.51 mmE= 200GPafo' = 24.2 MPa;Fy = 345 for Beam Fy = 248 for PlateLength of bearing plate is 150 mmUse LRFD Questions 1. Determine the safe uniform LL it could support to prevent web yielding.2. Determine the safe uniform LL it could support to prevent web crippling.3. Determine the safe uniform LL it could support due to the flexural strength of the bearing plate 150mmx250mmx30mm.