A bronze helical spring is subject to a compressive load of 1800 Ibf. The spring has 30 turns and 0.75 inch diameter wire on a mean radius of 6.10 inch. Determine the maximum shear stress and deflection in the spring? Also find the spring constant. Assume G = 7.5 x 10^6 psi.

A bronze helical spring is subject to a compressive load of 1800 Ibf. The spring has 30 turns and 0.75 inch diameter wire on a mean radius of 6.10 inch. Determine the maximum shear stress and deflection in the spring? Also find the spring constant. Assume G = 7.5 x 10^6 psi.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.29P: A polyethylene tube (length L) has a cap that when installed compresses a spring (with under-formed...

See similar textbooks

Related questions

Q: A cylindrical shaft made of steel of yield strength 700 MPa is subjected to static loads consisting…

A: Givenσy=700 MPaτ=σyF.S×0.58=7002.1×0.58=193 MPaM=10 kN=10000 NT=30 kN=30000 N

Q: et's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a…

Q: 8. A steel bar of 40mm x 40mm square cross-section is subjected to an axial compressive load of…

A: Answer: The elongation of the bar will be ◆ When 30mm × 30mm square section : 2.22 mm. ◆ When 40mm…

Q: If an isotropic material has a shear modulus of 21 Gpa and a Poisson's ratio of 0.4, calculate its…

A: The relation between Young's modulus, shear modulus, and Poisson's ratio is given as: E = 2G (1+μ) E…

Q: A rigid beam is supported by a pin at A and two metallic wires at B and C. Determine the force P…

Q: A steel rod placed between two walls is an exact fit and is stress-free at 20 degrees Celsius. Find…

A: The temperature at which the compressive stress becomes 100 MPa is 62.7350 ℃.

Q: re B 400 mm Sk ← 55 400 mm 60 kN ▾ Part A If the 20-mm-diameter rod is made of A-36 steel and the…

A: To find: The deflection in the rod. Given: The diameter of the rod is d=20 mm. The stiffness of the…

Q: A wire 20 m long, weighing 0.8N per m, and having a cross sectional area of 6.2 mm2, is suspended…

Q: Determine the nodal displacement of the bar shown in Figure 1 using two element of equal length. The…

Q: Q10/ Find the equivalent stiffness for the systems shown in figures below. K1 = 300 N/m Ks = 400 N/m…

A: First three parts will be done from multiple part questions. Please post again for other parts…

Q: 3. The steel pipe AB has a 72 mm outer diameter and a 5 mm wall thickness. Link CDE is rigidly…

Q: The composite bar consists of a 20-mm-diameter A-36 steel segment AB and 50-mm-diameter red brass…

Q: A simply supported beam of circular cross-section made up of hot rolled steel is subjected to a…

A: The fluctuating loads on a beam induce fluctuating stresses, which in turn lead to fatigue failure.…

Q: Situation 4: A rigid plate of negligible weight rests on the central spring as shown and is loaded…

A: Given: The load acting on central springs, P = 5+2x5+4 = 19 kN The gap between outer springs and…

Q: Spring Dimension: Spring 1 Spring 2 Steel Bronze Rigid bar of (1) (2) 150 mm Dm Dm 100 mm negligible…

Q: If an isotropic material has a shear modulus of 30 Gpa and a Poisson's ratio of 0.34, calculate its…

Q: A spring has a load of 50 lb with a spring index of 8. If the induced stress is 90ksi, determine the…

Q: A bronze bar (E = 103 GPa, v = 0.34) with initial dimensions shown is loaded with P = 80 kN. change…

Q: The steel plate shown below is put in into a rigid chamber, such that spacings of size s = 0.00188…

A: Write the expressions of normal strains. εx=1Eσx-νσy0.001884=1200×109σx-0.28σyσx-0.28σy=94×106…

Q: A rigid beam is supported by a pin at A and two metallic wires at B and C. Determine the force P…

Q: Question 15 of 15 Refer to the figure shown a = 11.7 x 10/°C a = 23 x 10/°C -6 %3D E 200 GPa 70 GPa…

Q: Cantilever steel rod is loaded by axial concentrated forces. F1 F2 F3 d 4 Given: 4-2,31; 12-2,91;…

A: Cantilever rod is one in which one of the ends is free from support and one end is fixed. The total…

Q: A rigid beam is supported by a pin at A and two metallic wires at B and C. Determine the force P…

Q: A leaf spring is to be made of seven steel plates 6-5 cm wide and 6.3 mm thick. Calculate the length…

A: A leaf spring is made up of seven steel plates that are 6.5 cm broad and 6.3 mm thick.We must choose…

Q: 2. The following handle is loaded at points B and C, as shown below. If the force P = A 0.8 m 40 mm…

Q: A cylindrical shape 25.0 mm in diameter and 21.0 mm in height is cut from a pear. Using an Instron…

Q: steel is subjected to a fluctuating load that varies from -F to +3F. Determine the minimum ultimate…

Q: The 21-mm-diameter A-36 steel rod is subjected to the axial forces shown. Take E = 200 GPa. (Figure…

A: Given Data D=21 mm E=200 GPa LAB=600 mm LBC=400 mm

Q: 2. A close -coiled helical spring having 12 coils must absorb 200 joules of energy and support a…

A: Given data⇒n=12 coilsE=200 joulesF=10 kNζ=220 MPaG=80 GPaProblem definition⇒Problem says determine…

Q: A weight of 320 lb falls through 6 ft and is then caught on the end of a wire rope 100 ft long…

Q: The rigid bar ABCD of negligible weight is initially horizontal, and the steel rods attached at A…

Q: A B D When the CD temperature rises by 60 ° C, calculate the internal force of the column with a…

Q: A rod has a diameter of 1/2 inch and a length of 4 feet. Determine the equivalent spring constant of…

A: given data; ⇒rod diameter (d)=12in=0.04166ft⇒length(l)=4ft⇒⇒young modulus (E)=10*106psi⇒spring…

Q: 3. If P= 100KN, Compute the total deformation. 1,2 m 201 60 CM 7P $=2ch $=6m E = 200 GPa = 100 GPO…

A: To find : The total deformation. Given that : The force is P=100 kN1000 N1 kN=10×104 N. The diameter…

Q: Q. After a puncture a driver is attempting to remove a wheel nut by applying a force of P KN to one…

A: Dear Student since you have posted a question with multiple sub-parts, but as per Q& A…

Q: A cantilever beam of circular cross-section is made of alloy steel is subjected to a fluctuating…

A: Given: σmax = 48 N/mm2 σmin = - 24 N/mm2 FOS = 2 Syt = 0.55 Sut σe = 0.45 Sut

Q: Determine the equivalent spring stiffness constant of the following.

Q: applied load of P = 480 N causes the upper frame to be deflected downward by 4.9 mm. Determine the…

Q: Determine the angle of tilt of the beam when the load is applied.

A: Given DataThe intensity of UDL load =600 N/mThe length of the beam CD =6 mThe spring constant A…

Q: Q Determine the elongation of the system shown in figure below

Q: The rod of 120cm long and 18mm diameter subjected to axial pull of 18kN. If modulus of Diameter =…

Q: Let's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a…

Q: The strains measured with a 60⁰ strain rosette are ϵa = R/3 x 10^-6 , ϵb= - R/2 x 10^-6 , and ϵc =…

A: Given data for 60o strain rosette, εa=R3×10-6εb=-R2×10-6εc=R8×10-6 The 60-degree strain rosette is…

Concept explainers

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.

Question

100%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A spring sustains 200 ft-lb of energy with a deflection of 3’’. Assume that the mean coil diameter is 7 times the wire diameter and that the allowable stress is 100ksi. Determine the wire diameter.
A close-coiled helical spring is subjected to an axial pull of 600 N. The spring is made out of a 16 mm diameter rod, and has 12 complete coils, each of mean diameter 120 mm. Compute shear stress induced in the rod and the deflection under the pull. Take G = 0.85 x 105 N/mm^2.
A safety valve spring having 9 and /2 coils has the ends squared and ground. The outside diameter of the coil is 115 mm and the wire is 13 mm. It has a free length of 203 mm. The length of which this spring must be initially compressed to hold a boiler pressure of 1.38 MPa on the seat of 32 mm diameter. Modulus of rigidity is taken as G=80GN/m2. a. Find the spring deflection and the operating length b. Calculate the solid length and the deflection of solid length c. Compute the solid force and the Wahl factor
A close-coiled helical spring is made of a wire of diameter 20 mm. The mean radius of the coils is 100 mm. Find the number of turns required and the maximum axial load permissible if the shear stress is not to exceed 100 MPa and the maximum elongation is limited to 40 mm. G = 83 GPa.
An open coiled heilcal spring made of 6 mm diam- eter steel wire and 60 mm mean coil diameter, with 60° inclination of the coils with the spring axis, is subjected to an axial torque T. If 1 number of turns in the spring increases by and original number of 8 turns is 12, calculate : (a) Magnitude of axial torque T, and (b) Change in axial length of the spring. Take E = 210 GPa and G = 84 GPa.
Please solve the problem step by step. Hope you know the hooke's law
3. Determine the torsional spring constant of the steel propeller shaft shown in Figure 2. |A В 0.3 m 0.2 m 0.25 m -0.15 m: В -2 m 3 m Figure 2. Propeller shaft
2. A helical valve spring is to be designed for an operating load range of approximately 90 to 135 N. The deflection of the spring for the load range is 7.5 mm. Assume a spring index of 10. Permissible shear stress for the material of the spring = 480 MPa and its modulus of rigidity 80 kN/mm2. Design the spring. 4С - 1 0.615 , C being the spring index. Take Wahl's factor %3D 4С - 4 [Ans. d = 2.74 mm ; D = 27.4 mm ; n = 6]
A square end compression helical spring has an operation load range of 3.5KN to 4.2KN.The deflection for the load range is 8mm and the spring index is 6.if the permissible shear stress and module of rigidity for the material of the spring are 380MPa and 90pa respectively, including the effect of the wire curvature. Design the spring by, determine (A)wire diameter (B) mean coil diameter (C) number of active turns (D)total number of turns
1. Design a compression helical spring to carry a load of 500 N with a deflection of 25 mm. The spring index may be taken as 8. Assume the following values for the spring material: Permissible shear stress = 350 MPa Modulus of rigidity = 84 kN/mm2 4С - 1 0.615 Wahl's factor where C-spring index. 4С - 4
A heavy-duty helical spring is to be made by wrapping a steel rod 10.6 mm in radius aroundforming cylinder 141 mm in diameter. If the elongation and shearing stress are limited to 161mm and 141 MPa, respectively. How many turns are required approximately? G = 83 GPa. Useapproximate formula for shear stress
Design a helical spring to be used in spring balance with a wire diameter of 6mm and the outside diameter should be limited to 66mm. if the permissible shear stress of the spring material is 325 N/mm? and the Modulus of rigidity is 85kN/mm?. a) Compute the deflection of spring per active turn and the axial load on the spring considering the effect of curvature, take Wahl's factor as Kw= 1.1 b) Calculate the value of axial load neglecting the effect of stress factor. **Note: Please upload your handwritten working/solution to the link provided. The value of Mean diameter of the spring in mm . The Spring Index is. Shear stress factor, neglecting curvature effect . Deflection per active turn in mm Axial Load W in N .. Axial Load W in N. considering effect of curvature .