A body with mass of 250 kg is supported by five 15 mm diameter cables. Determine the normal stress in each cables.

Q: A common bar suspended has an axial load of 1000 lb, it has a cross sectional area of 20 sq. in.…

A: Given data : The value of axial load P=1000 lb The value of cross sectional area A=20 in2   Required…

Q: Determine the stress produced in cylindrical rod of having diameter 2 mm when Tensile load of 44 KN…

A: Introduction : In this question we are provided with value of tensile load and cross section…

Q: A uniform beam weighing 500 N is held in a honzontal position by three vertical wires, one attached…

A: Stress = Load / Cross secrion  Assuming that the load is equally distributed in all the three wires.

Q: Problem 105 A homogeneous 800 kg bar AB is supported at either end by a cable as shown in Fig.…

A: Given : Weight of bar AB = 800 kg Allowable stress = 90 MPa in bronze Allowable stress = 120 MPa in…

Q: A hollow steel tube with an inside diameter of 80 mm must carry an axial tensile load of 330 KN.…

A:

Q: PROBLEM 1. The dimensions of a bar made of a 2024-T6 aluminum alloy and the loads acting on it are…

A:

Q: Determine the stress in a fiber (in psi) located 1inch from the top of the beam and 4 feet from the…

A:

Q: A load of 1950N is raised at the end of a steel wire. The minimum diameter of the wire so that…

A: Given data :- Load  = 1950 N Stress = 100 N/mm2 Calculate the minimum diameter of the wire

Q: A simply supported beam, 2 in wide by 4 in high and 12 ft long is subjected to a concentrated load…

A: FInd reactions:∑ MB=0RA12-20009=0R=1500lbMoment at midspan isMmid=15006-20003Mmid=3000 lb-ft

Q: The figure below shows a shaft of three segments It is restrained (fixed support) at both sides and…

A:

Q: Situation #3: A steel wire 12m long, hanging vertically supports a tensile load of 2 kN. Determine…

A: Length of steel wire (L) = 12m Vertically supports a load of (P) = 2kN = 2000N Stress = 140Mpa = 140…

Q: 17.6 A solid steel shaft 3 in. in diameter and 4 ft long is fixed at one end and free at the other,…

A: Given data  Diameter of shaft =3 in  Length of shaft = 4 ft  Axial tensile force = 50000 Lb

Q: A steel [E=200 GPa] rod with a circular cross section is 11 m long. Determine the minimum diameter…

A:

Q: A hollow steel tube with inside diameter of 100mm is carrying a tensile load of 400kN. Determine the…

A: Steel tube is given with, External Diameter of 115mm Internal Diameter of 100mm  Carrying a tensile…

Q: A beam has a cross-section that is 11inches tall and 4inches wide. If the max shear in the beam is…

A: Given Load 8 kipsDepth 11 inWidth 4 inTo find out Maximum shear stress

Q: A closely coiled helical spring of mean diameter 140 mm is made up of 12 mm diameter steel wire.…

A: GivenDiameter of helical spring D=140 mmRadius R=70 mmDiameter of steel wire which is used in spring…

Q: Please answer this question, An aluminum rod is rigidly attached between a steel rod and a bronze…

A:

Q: A cantilever beam, 80 mm wide by 280 mm high and 9 m long, carries a load that varies uniformly from…

A: We will find moment at 5 m from free end and use bending equation.

Q: 30 KN 1 m 10 KN/m 1 m 3m 10 KN/m

A:

Q: A cantilever beam. 80 mm wide by 260 mm high and 8 m long. carries a load that varies uniformly from…

A:

Q: i need the answer quickly

A:

Q: essed lengtns 74.98 n tress (psi) exists in the lo

A:

Q: A wood beam 150 mm wide by 300 mm deep is loaded as shown in the figure. If the maximum flexural…

A:

Q: Q1. The structure shown consists of a S18 x 70 rolled-steel beam AB and two short members welded…

A: Finding out SFD and BMD and maximum normal stress.

Q: A common bar suspended has an axial load of 10000 lb, it has a cross sectional area of 20 sq. in.…

A:

Q: An AISI 1020 steel rod 12 feet long is anchored between two rigid supports. At 68 degrees the rod…

A:

Q: A steel [E = 200 GPa ] rod with a circular cross section is 20 m long. Determine the minimum…

A:

Q: A force of 250 N is applied to one end of a 14 inches diameter circular rod. Determine the value of…

A:

Q: Compute the stress distribution of the beam shown in the figure at mid-section. Cross-sectional…

A:

Q: Situation 2: A hollow steel tube has an outer diameter of 90 mm and a thickness of 14 mm. Determine…

A: The basic concept of stress is ; Stress = Force Area σ = FA In terms of force it can be rearranged…

Q: A beam shown below, 200mm wide by 350mm deep, is loaded as shown in figure below. Determine the…

A: Given overhang beam with loading and asked to calculate shear stress below 50 mm from top fibre at…

Q: Problem 1.6. The ultimate stress, for a hollow steel column which carries an axial load of 1.9 MN is…

A:

Q: A seesaw weighing 3 lb/ft of length is occupied by two children, each weighing 90 lb. The center of…

A:

Q: A cantilever beam, 80 mm wide by 270 mm high and 8 m long, carries a load that varies uniformly from…

A: Hello dear The answer is found to be Stress at 60mm from top of the beam is found to be at a…

Q: A 2500 lb horizontal bar is supported by three 3/16-inch diameter wires as shown. The wires are…

A: Given:-P=2500 lb Diameter= 3/16 in L=20 feet=240 inches To find:- Stresses in wire Solution:-…

Q: A steel hollow pipe about 3m long which has the inside diameter of 15mm and outside diameter of…

A: Given Data : Length of hollow pipe, L=3m Inside diameter, Di = 15 mm Outside diameter, Do = 27 mm…

Q: In the following structure, determine the stress in each bar. Indicate whether the stress is tensile…

A:

Q: 1. A piece of wire 10-in long is tied vertically. The wire has a diameter of 0.1-in and is used to…

A:

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.