Answered: A block of wood is kept on table top.…

Name: A block of wood is kept on table top. The mass of wooden block is 5kg
Uploaded: 2024-03-20T06:56:46.000Z
Channel: Bartleby
Description: A block of wood is kept on table top. The mass of wooden block is 5kg and its dimensions are 40cmx20cmx10cm.Compute the force on top and bottom surface of the wooden block.

Science

Physics

A block of wood is kept on table top. The mass of wooden block is 5kg and its dimensions are 40cmx20cmx10cm. Compute the force on top and bottom surface of the wooden block

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 85PQ

See similar textbooks

Similar questions

A piece of wire of length 1.00 m is cut into two parts, one of which is bent into a shape of a circle and the other into the shape of a square. How should the wire be cut so that the sum of the enclosed areas is a minimum?
A 3500 kg statue is placed on top of a cylindrical object (Y= 2.3 x10^10 Pa). The stand has a cross sectional area of 0.073m^2 and a height of 1.8 m. Find the change in height of the object in meter.
you have been given indentical solid cylinders of three substances, oak, aluminum and styrofaom. Each of the solid substances are going to be dropped into liquid ethyl alcohol. you know that each cylinder has a radius of 5cm and a length of 8cm. you also know the weight of the substances are as follows Oak 4.3N, Alyminum 16.6N, styrofoam 0.03N. Determine whether each cylinder will sink, float or be neutral. show work.
a 300 kg cylinder that is horizontal. Three steel wires support the cylinder from a ceiling.Wires 1 and 3 are attached at the ends of the cylinder, and wire 2 is attached at the center. The wires each have a crosssectional area of 2.00 * 10-6 m2. Initially (before the cylinder was put in place) wires 1 and 3 were 2.0000 m long and wire 2 was 6.00 mm longer than that. Now (with the cylinder in place) all three wires have been stretched.What is the tension in (a) wire 1 and (b) wire 2?
A lead cube has a total mass of 50 kg. What is the length of the side?
The cross-sectional area of a wide-flange I-beam has the dimensions shown. Obtain a close approximation to the handbook value of Ix = 654 in.4 by treating the section as being composed of three rectangles. 0.380" & Answer: I - i 16.25" 7.073"0.628" in.4
What force must the driver of a car apply to a brake pedal which has an area of 0.03 m2 to produce 8 200 N of force on a 0.75 m2 (cross section area) brake cylinder connected to the brake pads on the wheel of the car?
One end of a wire is attached to a ceiling, and a solid brass ball is tied to the lower end. The tension in the wire is 385 N. What is the radius of the brass ball?
The owner of a company that manufactures drinking cups decides it would be impressive to build an inground swimming pool that is a scaled up version of her best selling cup. For this particular cup, the area of the circular opening at the top is 1.44 times the area of the circular bottom. Her pool contractor informs her that when the pool is full of water, the magnitude of the force acting on the top surface will be the same as the magnitude of the force acting on the bottom surface. Determine the depth of the pool. m Additional Materials O Reading Tutorial
You use a millimeter ruler to measure the height of a rail curb. The bottom of the ruler is resting on the table. The place where the height measurement is taken is a little curved, so it is difficult to identify very precisely where the measurement should be taken. Also, it's a bit tricky to make sure the ruler is perfectly vertical (it might be leaning forward or backward a bit). When you take the measurement, you measure 12.9 mm. By moving the ruler a little, you are confident that the correct measurement is somewhere between 12.7 mm and 13.3 mm. Indicate the value that you will record in your logbook, as well as the uncertainty that you will attribute to it. Give your answers in mm.
You use a millimeter ruler to measure the height of a rail curb. The bottom of the ruler is resting on the table. The place where the height measurement is taken is a little curved, so it is difficult to identify very precisely where the measurement should be taken. Also, it's a bit tricky to make sure the ruler is perfectly vertical (it might be leaning forward or backward a bit). When you take the measurement, you measure 12.9 mm. By moving the ruler a little, you are confident that the correct measurement is somewhere between 12.7 mm and 13.3 mm. Indicate the value that you will record in your logbook, as well as the uncertainty that you will attribute to it. Give your answers in mm. Warning: Keep at least 3 significant digits in your answers, even if it does not respect the rules of presentation of data in the laboratory.
A load of 250ON is applied to the lower end of a bone 0.2 m in length and 1.5 cm2 in cross- sectional area. Given the Y for bone as 2 x 1010 N/m2, compute the change in length of the bone.