A block of mass M1 resting on an inclined plane is connected by a string and pulleys to another block of mass M2 as shown in Fig. Find the tension in the string and acceleration of the blocks. Assume the coefficient of friction between the blocks M1 and the plane to be 0.2. M1=1500N , M2=1000N . Angle of inclined glane = 45 degrees

Q: the system blocks shown below is in equilibrium, the weight of block A is 10 kN and for block B is…

A: weight of block A=10 kNweight of block B=35 kNcoefficient of friction between A and surface,…

Q: 3. A V-belt drives a pulley at a speed of 1440 m/min. The coefficient of friction between belt and…

A: Given data: - The speed of the belt is v = 1440 m/min. The friction coefficient between belt and…

Q: From figure shown, block A weights 60 N and it is connected to block B using a light string that is…

A:

Q: A ladder of length 2L and mass M is positioned on level ground leaning against a wall such that the…

A:

Q: Determine the smallest force the man must exert on the rope in order to move the (162 kg crate shown…

A: 1 2

Q: The coefficient of kinetic friction between the 30-mm- diameter pin and the pulley is 0.25.…

A: (a) To find: The tension required to raise the load. Given: The radius of the pin is r=15 mm. The…

Q: Question 2 Consider the two blocks shown above, connected together by a massless rope around a…

A:

Q: A block R of mass 100 kg is placed on a block Sof mass 150 kg as shown in the figure. Block R is…

A:

Q: Q4/ See Fig. (4). What force P must the two men exert on the rope to slide the uniform 6 m beam of…

A: Solution  Given data- θ =30º                      L = 6m                      a = 0.6 m…

Q: 2. Block A weighs 100N and block B weighs 300N both rests on an inclined plane downward to the right…

A:

Q: Evaluate the mass of the Mo block shown in Figure 3 when the 100 kg block is almost situation called…

A: Mass of block m= 100 Kg Coefficient of static friction μs= 0.3 Angle of inclination θ= 200   To find…

Q: Figure Q3(b) shows two boxes, A and B hold each other on the ramp. If box A weigh X kg and the…

A:

Q: The 3000 kg front wheel drive SUV shown in the figure is attempting to tow the log along level…

A: Friction force the resistance offered by the surface to prevent motion, and normal force is the…

Q: 2.4 m w A uniform ladder 4.8 m ft long and weighing W lb is placed with one end on the ground and…

A:

Q: A block of mass m₁ = 1.95 kg and a block of mass m₂ = 6.45 kg are connected by a massless string…

A: m1=1.95kg m2=6.45kg M=10kg R=0.250m N=10kg θ=30° μ=0.36 We need to find Acceleration of the two…

Q: A heavy cask (full of wine!) sits on an inclined plane. It is held in place by a rope that is…

A:

Q: 2. Compute the horizontal force P required to prevent the block from sliding down the plane for the…

A: GivenW=100 lbθ=30oμs=0.65

Q: 106 lb crate is initially stationary. Coeffi- cients of friction between crate and inclined surface…

A:

Q: The uniform 4.9-m pole has a mass of 230 kg and is supported as shown. Calculate the force Prequired…

A: Given that ,  m=230gW=230×9.8=2256.3NμB=0.28θ=tan-12.33.2=35.71°

Q: An 90.17 kg person is half way up a uniform ladder of length 3.939 m and mass 29.49 kg that is…

A: Here we will apply equilibrium conditions.

Q: A filled barrel has dimensions of a = 0.55m, b = 1.1m, and c = 0.6m, a total mass of 108kg, and has…

A:

Q: Q4(a) Figure Q4(a) shows a dissected 50-kg wooden spool supported by a cable at B and against the…

A: Given,

Q: For the given illustration below, determine the value of force F to remain the figure at rest. Use…

A:

Q: Two block A and B are connected by a rope which wraps areound a peg with static coefficient of…

A: Static coefficient of friction µ= 0.2 The weight of block B WB = 50-lb Force at block B   F=35-Ib…

Q: A cube with mass of m=80N is on the inclined plane with angle of phi=20 degrees. coeficient of…

A: Given:Weight of the mass, W=80 NAngle of the slope, θ=20°Coefficient of statis friction,…

Q: Answer the question shown in the images. Show every step

A: The maximum mass of the block C is mc=54kg The maximum mass of the block B is mb=mb+8=70kg

Q: Q: Block(A) of weight (100KN) is tied to block (B) of unknown weight (WB) through a flexible cable…

A: Given, Weight of block A = WA = 100 kN Coefficient of friction between A and its resting surface =…

Q: Activity 1. A 25-kg ladder, 4 m long, rests on a rough floor and against a vertical wall. The ladder…

A:

Q: 7. In Figure 6, the cups and the ams of an anemomcter are fabricated from a material of density p.…

A: “Since you have asked multiple questions, we will solve the first question for you. If youwant any…

Q: If a piece of block weighing 150 kg is to be pulled up by a winch using two cables on a 25 deg…

A: Frictional force is formed when two surfaces attempt to move in the same direction or in opposite…

Q: A block with a mass of 100 kg (left-block) is connected to another block of mass M (right-block) by…

A:

Q: A file cabinet weighing 215 lb is being pushed to the right with a horizontal force P applied a…

A: The maximum height at which the cabinet can be pushed and the acceleration of the cabinet. Given:…

Q: A 20-kg triangular block sits on top of a 10-kg rectangular block shown in the figure below. The…

A: given data; mass of triangular block(M) =20kg mass of rectangular block(m)=10kg friction coefficient…

Q: (b) In figure, the two weights are released from rest. The coefficient of kinetic friction between…

A: coefficient of friction = 0.18 find the tension in cable.

Q: Crates A and B, shown in Figure Q4, weigh 20 kg and 15 kg, respectively. The crates are connected…

A:

Q: In the figure shown the blocks weighs 400 N each. It is held in the position by a belt that passes…

A:

Q: A uniform ladder of length 12 mand mass 30 kg rests with one ed on rough horizontal ground and the…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.