A belt conveyor is required to deliver crushed limestone having a bulk of 75 lb/ft³ at the rate of 200 tons/h. The conveyor is to be 200 ft between centers of pulleys with a rise of 25 ft. The largest lumps are in 4 inch and constitute 15% of the total. The conveyor will discharge over the end. For the speed of 200 fpm, the horsepower for the drive power is. a) 8 hp b) 11 hp c) 20 hp d) 25 hp

A belt conveyor is required to deliver crushed limestone having a bulk of 75 lb/ft³ at the rate of 200 tons/h. The conveyor is to be 200 ft between centers of pulleys with a rise of 25 ft. The largest lumps are in 4 inch and constitute 15% of the total. The conveyor will discharge over the end. For the speed of 200 fpm, the horsepower for the drive power is. a) 8 hp b) 11 hp c) 20 hp d) 25 hp

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter5: Separation Processes

Section: Chapter Questions

Problem 5.14P: Two materials, A and B, are to be separated using two unit operations, 1 and 2. The feed has 10...

See similar textbooks

Similar questions

Not sure how to do this one. Would really appreciate a full solution. Thank you!
A 198 hp (power-shift) dozer is used in a pushing operation. The dozer is equipped with a straight blade. The material (dry and noncohesive) weighs 97 pcf in the bank state. It is estimated the material will swell 6%, from bank to loose state. The center-of mass–to–center-of-mass pushing distance is 200 ft. Job efficiency can be assumed to be equivalent to a 50-min hour. Calculate the production in bcy per hour and the direct cost of the proposed earthmoving operation in dollars per bcy. The company’s normal O&O cost for these machines is $135 per hour and the operator’s wage is $50.00 per hour plus 36% for fringes, insurance, and worker’s compensation.
figure below shows the proposed design for a hydraulic press used to compact solid waste. A piston at the right is capable of exerting a force of 12500 lb through connecting rod to the ram. The rod is straight and centrally loaded. it is made from AISI 1040 OQT 1100 steel (Sy=80x10^3 psi, E=30x10^6psi. compute the resulting design factor for this design. specify the required diameter of the connecting rod if it is made as a solid circular cross section. Use design factor of 4.0. ompute the resulting design factor 101 Solid waste to be compacted Emn A Ram Weld A-18m² I= 4.5int Connecting rod 12.75 ft Pin A 2.00 in Section A-A Piston 3.00 in 12 500 lb I= //12 H=4 n=0.
Two materials, A and B, are to be separated using two unit operations, 1 and 2. The feed has 10 tons/h A and 4 tons/h B. The split (fraction of material rejected by each operation) is given in Table P5-14. a. Which sequence of operations, (l?2) or (2?1), will yield the greatest recovery of material A? b. What will be the purity of material A using that sequence? c. What will be the efficiency of separation for the entire process train with regard to material A using the Worrell-Stesed equation?
A beam is loaded as shown in the diagram. Draw the S.F. and B.M. diagrams and find: (i) maximum S.F. (ii) maximum B.M.(iii) point of inflexion. 50 kN 2m $ 50 kN 40 kN 2 m2.33 m 2 m $ 40 KN | 2m →
Q) An engine lathe is used to turn a cylindrical work part 150 mm in diameter by 500 mm long. Cutting speed 2.50 m/s, feed 0.30 mm/rev, and depth of cut 3.0 mm. Determine (a) cutting time and (b) metal removal rate.
QA Fora flow rate of 300 iter/second ata velocity of 1.3 meters/secand, design a seamless. steel Take factor of safety of 2.5, Longitudinal efficiency ofjoint, 1 = 0.50, and intesnal pressure= 4 Nl
Determine the area of a support used on a concrete conveyor where the loaded weight is 700 lb and the unloaded weight is 120 lb. Consider the Gerber criterion kt=.8, N=4 and an AISI 301 1/2 material, hardness subjected to bending and with 99.9% reliability.
box all final reactions required in each item
In (Figure 1), k = 180 N/m. Figure 2 m -2 m D -3 m- wwwwww 1 of 1 Part A Determine the unstretched length of DB to hold the 40-kg crate in the position shown. Express your answer to three significant figures and include the appropriate units. 1 = O Ti Value Submit μA Provide Feedback Request Answer Units
Question 1 For the shaft in figure below, the given information's are: • Power 20 KW, at 500 rpm • Ultimate tensile stress 170 MPa • Ultimate shear stress 130 MPa • Factor of safety 1.75 Determine the diameter for the shaft? 3000 N 1500 N vertical load FRA lRe diagram 5000 N hori zontal load oliayram Ra RA
need solution in 1 hour