A beam with rigid support at A, pin connection at C and roller at D has the geometry and loads as shown in the figure and parameter table. Find the equations for the shear and moment as a function of z in each segment of the beam. Follow the sign convention that positive shear tends to rotate the object clockwise, and a positive moment would tend to bend the object concave up. Take the origin for all functions to be at A. D parameter value units 790 N-m 350 N/m 2. L2 2. L3 Segment AB (0 m

A beam with rigid support at A, pin connection at C and roller at D has the geometry and loads as shown in the figure and parameter table. Find the equations for the shear and moment as a function of z in each segment of the beam. Follow the sign convention that positive shear tends to rotate the object clockwise, and a positive moment would tend to bend the object concave up. Take the origin for all functions to be at A. D parameter value units 790 N-m 350 N/m 2. L2 2. L3 Segment AB (0 m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter10: Statically Indeterminate Beams

Section: Chapter Questions

Problem 10.4.6P: A beam with a sliding support at B is loaded by a uniformly distributed load with intensity q. Use...

See similar textbooks

Similar questions

A beam ABCD with a vertical arm CE is supported as a simple beam at .1 and D (see figure). A cable passes over a small pulley that is attached to the arm at E. One end of the cable is attached to the beam at point B. The tensile force in the cable is 1800 lb. Draw the shear-Force and bending-moment diagrams for beam A BCD. Note: Disregard the widths of the beam and vertical arm and use centerline dimensions when making calculations. Repeat part (a) if a roller support is added at C and a shear release is inserted just left of C (see figure part b).
Repeat Problem 6.4-14 but use the configuration of channel shapes and loading shown in the figure. Use P = 250 N.
Frame ABC has a moment release just left of joint B. Find axial force N, shear force V, and moment M at the top of column AB. Write variables N, V, and M in terms of variables P and L.
A simply supported beam ABC is loaded at the end of a bracket BDE (see figure). Draw axial-force, shear-force, and bending-moment diagrams for ABC.
A beam with a sliding support at B is loaded by a uniformly distributed load with intensity q. Use the method of superposition to solve for all reactions. Also draw shear-force and bending-moment diagrams, labeling all critical ordinales.
Find expressions for shear force V and moment M at x = x0of beam AB in terms of peak load intensity q0and beam length variable L. Let x0= L/2.
Repeat Problem 10.4-41 for the loading shown in the figure.
For the beam illustrated in the figure, find the locations and magnitudes of the maximum tensile bending stress due to M and the maximum shear stress due to V. Parameters are a = 310 mm, b= 135 mm, c = 20 mm, h = 40 mm, and F= 4350 N. a mm FN bmm The moment of inertia is C mm hmm |x105 mm4. The maximum tensile bending stress due to Mis The maximum shear stress due to Vis MPa. MPa.
Q1: For the beam Shown in Figure 1 16KN 4kN/m 4kN/m .A C B 3m 2m 2m 3m Figure 1 I. Find the reaction at support A RAy II. Find the reaction at support B RBy II. Find the bending moment at A IV. Find the bending moment at C V. Find the maximum absolute value of the shear force in the beam VI. Draw the shear force and bending moment diagram for the beam
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a-3.25 m, b=4.75 m, Pg - 35kN, and Pc = 80kN. Construct the shear- force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. A Ay- 58.66 - Dy- Calculate the reaction forces A, and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) Answers: a 56.33 (a) V= (b) V- (c) V- B i i PB B kN с kN C Determine the shear force acting at each of the following locations: (a) x-2m (b)x - 4 m (c) x-8 m Note that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2. 3 3 3 KN D b kN D ·x Dy
The figure shows a cantilevered beam, subjected to a uniformly distributed (rectangular) 40 N/m force along the section DE, a 50 N point force at point C, and a 200 Nm couple moment. a. Write the shear-force and bending-moment equations as a function of distance, x, measured from the leftmost point, A, for the entire beam. b. Using your shear-force and bending-moment equations, calculate the shear force and bending moment at x = 2 m and x = 5 m. 200 N·m A 2.5 m 50 N CV D 1 m 40 N/m ↓↓↓ 2.5 m E B 2 m
A beam with rigid support at A, pin connection at Cand roller at D has the geometry and loads as shown in the figure and parameter table. Find the equations for the shear and moment as a function of z in each segment of the beam. Follow the sign convention that positive shear tends to rotate the object clockwise, and a positive moment would tend to bend the object concave up. Take the origin for all functions to be at A. |C D parameter value units 910 N-m w 400 N/m 4 m L2 L3 3 Segment AB (0 m