A beam with an S380 × 74 section carries a total uniformly distributed load of 3W and a concentrated load W. Determine W if the flexural stress is limited to 120 MPa. S(section modulus) = 1 = 1060 x 10° MPa 5W W B * 1m- 1m By 3m Ấy Value of reaction By Moment(maximum) in terms of W Value of intensity, W %3D II II

A beam with an S380 × 74 section carries a total uniformly distributed load of 3W and a concentrated load W. Determine W if the flexural stress is limited to 120 MPa. S(section modulus) = 1 = 1060 x 10° MPa 5W W B * 1m- 1m By 3m Ấy Value of reaction By Moment(maximum) in terms of W Value of intensity, W %3D II II

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

OOKN GOKN K B 75KN 75KN 75 KN G@ Am = 24 m %3D Determine the Miember force on member EJ.
At which point on the design P-M interaction diagram is the design flexural strength largest? O Pure compression Pure tension Balanced failure point (CCL limit) O TCL limit Beam condition (Pn = 0) %3D //img00.zhaopin.cm
(2) 4 0 5 211 5 4 #9 4 "1 16 #3" ft-k fé = 3 ksi, M = 90 NWC. The section is cracked. Computer the bending stresses in the beam by using transformed-area metho
OOKN GOKN K B 75KN 75KN 75 KN G@ Am = 24 m %3D Determine the Miember force on member EJ. 1 2m Im
Question 15 The design shear resistance, Vpl.Rd of a fully restrained simply supported Universal Beam with yield strength 345 N/mm² is 1,285 kN A point load of magnitude 1,906 kN is applied at the beam's mid-span The area of the web of the beam is Aw = 5,505 mm² The plastic modulus is Wpl.y = 2,979 cm³ The thickness of the beam web is tw = 12.6 mm Find the reduced design moment of resistance of the beam Mc,Rd (use the formula for l-cross-sections with equal flanges and bending about the major axis) Give your answer in kNm to the nearest whole number. Do not include units in your answer.
* TRUTT 50 kN/m 8m TIZI SLAB THICKNESS 150mm 2500 mm fe'= 21 MPa fy = 414 тра Cc = 40mm spacer barp=25mm Say bw= 0.6h DESIGN THE T-BEAM AND SHOW THAT TENSION STEEL YIELDS AND THE BEAM IS TENSION CONTROLLED
1) Find the allowable safe loadpf the stressec in the ban are fhe following BC - so ksi ABE GO feri CD = 70 ksi 0.4 in2 0.5 n2 0.3 n? op - P4 A 13
QL/ Twe rad have the Same cross- Sectional area; Mad from steel anel Bron ze as shown in fig1. Find the stress in each rood when Est = 200GPa j Eb=83Gpa. br st 3m 30 30 Fig1
Safe Support Spacing and S-1-bd Table below shows formulas for shear, bending moment and deflection for three-span continuous uniform load beam. R₁ = R₁ = 0.4wl R₁ = R₁ = 1.1wl V V Vmax=0.6wl Vdes = 0.6wl-w M M w(² Mmax= 10 A AMEE we Amax 145E'I If the bending and shear stress equation, and allowable deflection values are given as follow: • fb = M/S • fv = 3V/2bd • A = 1/16" a- Calculate safe support spacing for this beam (express the safe support spacing as a function of several variable). b- Express the equations for section modulus, moment of inertia and bd. Three-span, continuous, uniform l | = -w (d+ 12 )
4 - For the beam loading configuration and cross-section shown below, what is the maximum allowable load P given that the maximum allowable stress (in tension and compression) is 120 MPa? PO Р 1.6m PN ż 0.8m 0.8m P80 1.6m Р 30 30 T 10 dimensions in mm beam cross-section (same as problem 3, but inverted)
3G “. Asiacell %99 Home Work... adhomShupper H.W. 1: 4.3 m Two axial members are used to support a load P applied at joint B. • Member (1) has a cross-sectional area of A = 3,080 mm2 and an allowabl normal stress of 180 MPa. • Member (2) has a cross-sectional area of Az = 4,650 mm2 and an allowable normal stress of 75 MPa. Determine the maximum load P that may be supported without exceeding either allowable normal stress. 5.0 m 2.0 m
Calculate the shear stress in MPa at section B A 100 mm F-10EN 10 mm