A beam 10 m long is simply supported 1 m from each end. It is made of two C 380 x 50 channels riveted back to back and used with the webs vertical. Determine the total uniformly distributed load (KN/m) that can be carried along its entire length without exceeding flexural stress of 120 MPa. -C 380 X 50 W N/M A B R

A beam 10 m long is simply supported 1 m from each end. It is made of two C 380 x 50 channels riveted back to back and used with the webs vertical. Determine the total uniformly distributed load (KN/m) that can be carried along its entire length without exceeding flexural stress of 120 MPa. -C 380 X 50 W N/M A B R

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Figure shows a rigid beam ABC which is supported by member BD. Determine i. the reaction force at pin A ii. the resultant internal loadings acting on the cross section a-a. 0.80 m 0.60 m A B C 30° 0.4 m F = 800N 1.50 m D
Analyze the beam for stresses at point A and B due to combined effect of loading. Force F is equal to 5000 lbs and P is equal to 3500 lbs.
For the section shown, by what amount is the moment of the timber increased by the steel plates if n=15 and the allowble stressus are 0 = 120 MPa and = 8 MPa. Isom WALL RZESZED 111 250m 300m
As the safe normal stress of the wood used for the beam and loading condition shown in the figure is 12 MPa, determine the optimum cross-section height (mm) of the beam.
All pins are in double shear, each has a diameter of 13mm, and the average shear stress in each pin is not to exceed 65 MPa. Determine the maximum magnitude P of the loads that the beam can support
Two 8-in.-wide wooden boards are to be joined by splice plates that will be fully glued onto the contact surfaces, as shown in the figure. The glue to be used can safely provide a shear strength of 145 psi. Determine the smallest allowable length L (in inches rounded to the nearest hundredths) that can be used for the splice plates for an applied load of P = 14,000 lb. Note that a gap of a = 0.6 in. is required between boards (1) and (2). •.. - L (1) (2) a
Please show intermediate steps including free body diagrams, equations used, and problem setup so that your approach can be followed
Given the beam and the loading shown below, if L = 5 m, W1 = 4.5 N/m and w2 = 22.3 N/m. Calculate the vertical reactions at the supports. W2 w(x)=w, +ax³ L A B X Reactions: Ay = 单位 (tolerance 0.5 N) By = |数字单位 (tolerance 0.5 N)
Part A The built-up beam in (Figure 1) is subjected to an internal moment of M = 50 kN · m Determine the amount of this internal moment resisted by plate A. Express your answer to three significant figures and include appropriate units. НА ? ха х.10п Figure < 1 of 1 M= 32.9466 KN • m 150 mm 9 The unit you entered is not recognized. Review a list of acceptable units. No credit lost. Try again. 20 mm 150 mm 150 mm 10 mm Submit Previous Answers Request Answer M Provide Feedback 10 mm 300 mm
A 4-m cantilever beam is loaded as shown. The cross section is formed with two concentric circles of radii 45 mm and 35 mm. If the allowable stress is 150 MPa, Ra 1 X 12 h Find the allowable maximum value of F. Select the correct response: 2.898 KN 2.269 KN 3.606 KN 4.392 KN < Previous Ri
From the given figure below, determine the flexural stress of the beam at fixed end if it has a cross section of 150mm wide by 250mm deep. HA VA 0 1750 40 N/m 3m -420Nm B & Im 550 35 N -75Nm с + 0° 55'N 20N 20N 0° DAV-DIAG -20Nm M-DIAG
1. The horizontal beam is assumed to be rigid and supports the distributed load shown. Determine the vertical reactions at the supports. Each support consists of a wooden post having a diameter of 120 mm and an unloaded (original) length of 1.40 m. Take Ew = 12 GPa. The horizontal beam is assumed to be rigid and supports the distributed load shown. Determine the angle of tilt of the beam after the load is applied. Each support consists of a wooden post having a diameter of 120 mm and an unloaded (original) length of 1.40 m. Take Ew = 12 GPa. 18 kN/m A B C 1.40 m 2 m +1m-