A bar of gold (Au) is in thermal contact with a bar of silver (Ag) of the same length and area (see figure below). One end of the compound bar is maintained at T= 119 C and the opposite end is at 0.2 C. When the energy transfer reaches steady state, what is the temperature at the junction (in "°C)? The thermal conductivity of gold is 314 and silver is 427 (W/m ° C). T

A bar of gold (Au) is in thermal contact with a bar of silver (Ag) of the same length and area (see figure below). One end of the compound bar is maintained at T= 119 C and the opposite end is at 0.2 C. When the energy transfer reaches steady state, what is the temperature at the junction (in "°C)? The thermal conductivity of gold is 314 and silver is 427 (W/m ° C). T

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 14RQ

See similar textbooks

Similar questions

The current through the diode in the circuit given in the Figure below when Vy = 0.7 V is? ww 8092 12V Select one a. 24.26 mA b. 13.09 mA c. 58.23 mA d. 40.13 mA 40-52 ww 3092 ID
Electrical Engineering please solve this thank you The following values are given for a shocdley diode Vi (derel vollaye) • 0.025 V Is (Deverse salunalia cmal): 10X10A -15 Given voltaye eg ^: v(t) = 0.7+ 8 Vr cosut IA RL= 50 0 %3D Find avg. powen diipted in shochly diode € ay.power deliveud to load
A simple p*n junction is designed to work as IMPATT diode. The doping concentrations in the p* layer is 1019 cm-3 while the doping in the n-layer is 0.7 x1016 Calculate the peak electric field if the breakdown voltage is 80 V and the dielectric constant is 11.9. Express your answer in the unit of kV/cm. cm-3
Aluminum has a resistivity of 10.6×108 Nm at 20°C. What will the resistivity of Aluminum when then temperature is increased to 1000°C. (Take a as 2.65×10-³)
The voltage sensitivities of Barium Titanate and Quartz are respectively 12 X 10-3 Vm/N and 50 X 10-3 Vm/N. Their respective permittivities are 125 X 10-8 F/m and 40.6 X 10-12 F/m. What are their charge sensitivities?
Q: - Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. 4:1 D, 120 V rms c) If sin wave with 100µf connected in parallel with the resistor, calculate the ripple сарacitor is 60 HZ 1.0 kN D2 factor lllee lelll
Q1: In common coordinate systems draw the V-A characteristics of Si diode and Ge diode for T=25C.
The voltage sensitivities of Barium Titanate and Quartz are respectively 12 × 10-³ Vm/N and 15 × 10-3 Vm/N. Their respective permitivites are 12.5 × 10-⁹ F/m and 40.6 × 10-12 F/m. What are their charge sensitivites?
Find the current through the diode in the circuit shown. Assume the diode to be ideal. A 50 92 www R₁ V = 10 V O 185 mA O 46 mA O 140 mA O 28 MA 502 R₂ B D
1. 1-5 K 30v a. what is tue T CTime constant) ? b. How long will it take for the capacutor TO rtach s0% op charge? C. What is tne voltage of capa citor apter 1 seconds? d. How many tíme constants will it take for the soltage to reach 23 v? C. Gweng that the capacitor is fully changed, how will it take por it to be 20% ? long 120v + BF what is the. T ? b. what is the voltage capacitor apter 10 sec? a. C. How many time constants will it take for Tue Vo Itage to reach 80 v.? d. Given that the capaator is Fully charged, how time constants will it be to reau many GOV!
8. Liquids with solid impurities a) Have higher dielectrie strength b) Of large size have higher dielectric strength c) Have lower dielectric strength as compared to pure liquids d) None of the above 9. Peak to peak ripple is defined as a) the difference between average de voltage and peak value b) the difference between maximum and minimum de voltage c) the difference between maximum ac and average dc voltages d) the difference between ac (rms) and average de voltages 10. In a Cockroft-Walton circuit, input voltage 100 kV load current 25 mA, supply frequency 100 Hz, each capacitor 10 nF. The optimum no. of stages for maximum output voltage is a) 1 b) 2 c) 10 d) 35
AN Sesli oku 1-In the circuit designed to measure the effective value of the sinusoidal voltage at the input, diodes are considered ideal. M deflection is a measuring element with rotating coil. Rm32k İm-(10)^-4 A. A- Draw the waveform of the current flowing through M on a scale. Determine the resistance value of R1 so that the nominal voltage value of V-m is 100V. B-What should the tolerances of the resistors be so that the Vm class is at most 1.5? (resistors have the same tolerances) ult) R2 本 R3 20k 18k R4 k: k2 10k