A bar assembly ABC is loaded with axial force 'P' is constrained at both ends. Analyze a bar element by i) ii) A Determining the reactions at either ends. Determining the reactions at either ends when the joint C is reduced by 'u' mm from wall/constraint joint C. 0.7 L B P 0.5 L с

A bar assembly ABC is loaded with axial force 'P' is constrained at both ends. Analyze a bar element by i) ii) A Determining the reactions at either ends. Determining the reactions at either ends when the joint C is reduced by 'u' mm from wall/constraint joint C. 0.7 L B P 0.5 L с

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Z Z Z I = Ax IM IN Ay By

Q: (a) the normal stresses in the bronze and steel rods o1,02 (positive if tensile, negative if…

Q: Wニ SOKN 20km II I JB solve for: the Cocation of Ivalue of maximum deflection in terms of EI. 4. 3m…

Q: The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E…

A: Given data in question Load 88 kN Area 520 and 280 mm2 Elasticity modulus 110 and 67 GPa To find…

Q: Determine the reaction at H in the given truss

A: ake moment about A∑ MA=0

Q: A rigid rod AB is attached to a hinge at 4 and to a spring with stiffness Eat D. The critical…

A: Rigid rod AB attached to spring at D

Q: Determine the reactions at A and B for the steel bar and loading shown, assuming a close fit at both…

A: Given data:- Conditions given-Remove restriction at A and solve for the reactions Below bar figure…

Q: X= 482 Y= 82 A= 9 SHOW COMPLETE SOLUTIONS

A: As per guidelines we need to answer only first 3 subparts of question so please repost rest…

Q: For the uniform beam shown, use superposition to determine the reaction at each of the three…

A: A simply supported continuous beam is shown in the above figure. A point load of P and another point…

Q: A simple frame is loaded and supported by a pin at A and a roller at B as shown in the Figure 2. The…

Q: Az reaction at A, horizontal component Ay reaction at A, vertical component A X 6 m Press [ESC] to…

Q: Find the internal force in the truss member CB. CB = KN, Compression %3D 1 kN

Q: The truss is supported on a roller at A and a hinge at B. Solve for the components of the reactions.…

A: Horizontal load at D= 340 lb Vertical load at E= 700 lb Vertical load at C= 500 lb

Q: 022 Plate 3-Method of Consistent Deformation Determine the force in member CD of the truss shown in…

Q: . 4-Determine the reactions at the supports for the frame shown below try the method of consistent…

A: Step 1 Given data To determine :Reactions at the supports RA and RB

Q: The asymmetric simple truss is loaded as shown. Determine the reactions at A and D. Neglect the…

A: Reference : Structure Analysis, Truss Analysis.Given :Forces acting at each points A, B, C and DTo…

Q: For the given truss below, take P = 20 kN, L=2 m, and H= 6 m to solve the followings: %3D H L 1.…

A: Given P=20kN L=2m H=6m

Q: Determine the support reactions at A and D where a = 3m

A: Find the support reactions at A and B

Q: The pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar (1) is an…

Q: The frame ABC is loaded as shown, determine the support reaction. 5kN/m 5kN/m 4m B 3m

Q: The following steel shaft (1) is rigidly connected at B to another aluminum shaft (2). Both shafts…

A: Gs = 80 GPa = 80 × 103 N/mm2 GAl = 28 GPa = 28 × 103 N/mm2 Rotation of support C = 0.001 rad…

Q: Calculate the force in member AB in kN Calculate the force in member Al in kN Calculate the force in…

A: Given- truss carrying a total load of 5F, where F=1000Kn support A is hinged and support H is…

Q: 1.) Determine the force in member FE. (N) 2.) Determine the force in member EC. (N) 3.) Determine…

Q: O a) 0 ОВ) 10.5 OC) 19.5 O D) 6 то) 4

Q: The braced frame (vertical truss) has a hinge support at point A and a horizontal roller support at…

A: Solution: Considering the diagram ∑Fx=0HA=44+80=124 kNTaking moment across point…

Q: The truss shown is supported by a hinge at A and a roller at B. A load of 2500 lb is applied at C.…

Q: The compound beam is pin supported at C and supported by a roller at A and B. There is a hinge (pin)…

A: Given data in question Load 4k, 1k & 27 k Angle 30° Span 19 ft Internal hinge at D Statically…

Q: H.

Q: Determine the force in each member of the truss A 60° B -Am -Am- -Am 60 D YkN

Q: The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E…

Q: Problem 5: Inputs: a = 1.75 m b = 2 m ● c=1m d=2 m ● ● ● ● h = 2.5 m F₁ = 12 kN F₂ = 8 KN This frame…

Q: The A-36 steel rod has a diameter of 60 mm and is firmly attached to the rigid supports at A and B…

Q: find deflection, shear at a and b

A: Summary of ResultsShear at A: VA = − 5 kNShear at B: VB = − (L + 5) kNDeflection at…

Q: Calculat reactions at pin support A and edge B, take beam weight 35 Kg 1 т 3 m B 50° A

A: For calculating the reactions equilibrium conditions must be followed: Sum of all the forces among…

Q: D. D 1083 N

A: Data Given: Asked: Resultant force in member AB

Q: For the uniform beam shown, determine the reaction at each of the three supports

A: Given :- A uniform beam is shown with two point load P and 2 P To determine :- The reaction at each…

Q: SOLVE FOR THE FORCE IN EACH MEMBER 600N 400 N 545 6m 45° 3m

Q: Question 6 Using the flexibility method, determine the reactions at the supports A and D in the…

Q: A load of P = 80 kN is supported by a structure consisting of rigid bar ABC, two identical solid…

Q: 3.9 kN 4.0 kN 2.0 m 2.0 m 1.1 m 2.2 m D E

Q: Determine the degree of determinacy of the structure shown below. Put "-1" if unstabl "0" if…

Q: Classify each of the structures as statically determinate, indeterminate or unstable. If…

A: Diagram (d) and (e) are provided. We have to find out determinacy/Indeterminacy and stability of the…

Question

100%

Span "L" in metre
Displacement 'u' mm
P (KN)
AB section Area
BC section Area
E (Gpa)
7.1
0.12
50.00
700
200
195

A bar assembly ABC is loaded with axial force 'P' is constrained at both ends. Analyze a bar
element by
i)
ii)
A
Determining the reactions at either ends.
Determining the reactions at either ends when the joint C is reduced by 'u' mm from
wall/constraint joint C.
0.7 L
Figure 1
0.5 L
U

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 110 GPa] with a cross-sectional area of A₁ = 630 mm². Bar (2) is an aluminum alloy [E = 79 GPa] with a cross-sectional area of A₂ = 340 mm². A concentrated load of P = 52 kN acts on the structure at D. Assume L₁=910 mm., L₂=430 mm., a=450 mm., b=280 mm., and c=1030 mm. Determine: (a) the normal stresses 0₁, 02 in both bars (1) and (2). (b) the downward deflection vp of point D on the rigid bar. a 5 Answers: (a) 6₁ (b) VD= = tel i (1) L₁ L2 B C MPa, 0₂ = mm. i MPa
SOLVE WITH SOLUTION.
The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 92 GPa] with a cross-sectional area of A₁ = 680 mm². Bar (2) is an aluminum alloy [E = 74 GPa] with a cross-sectional area of A₂ = 350 mm². A concentrated load of P = 56 kN acts on the structure at D. Assume L₁=900 mm., L2=600 mm., a=580 mm., b=310 mm., and c=1160 mm. Determine: (a) the normal stresses 01, 02 in both bars (1) and (2). (b) the downward deflection vp of point D on the rigid bar. b Answers: (a) o₁ = (b) VD= i i L₁ L2 (2) B C MPa, 0₂ = mm. i D MPa
Determine the force in member FG (assume FG is tension) of the truss shown in the figure below?. Set P = 671 lb. 2P 12h 12 12 12 Answer:
7. Distributed Loads A beam supports a distributed load as shown. (a) Determine the equivalent concentrated load (b) Determine the reactions at the supports. wB = 4500 N/m WA = 1500 N/m %3D A -L 6 m-
find all the reaction for the frame by the slope deflection method
The asymmetric simple truss is loaded as shown. Determine the reactions at A and D. Neglect the weight of the structure compared with the applied loads. Is the knowledge of the size of the structure necessary? 1L 60° Answers: Ay = i Dy= Dx= i i B 3L 60° 60° E y 1 1L L L L 30° x 4L D
NO.4 SOLVE FOR DE
From the given truss shown: F= (0.25)(Birth month)(birthdate) Newton Example: if your birthday is December 28 you F= (0.25)(12)(28)= 84 N (a) What is your birthday (Month and Day) (b) What is the value of your F? (c) Calculate the reaction at the support. (d) Using the METHOD OF JOINTS, determine all the forces carried by each member of the truss, state whether the members is under tension or compression. Make a summary table of the forces and orientation carried by each member. 3 m 6 m
Please help me answer the following Analysis of structures.
From the following armor, determine the following: Reactions in A and F. The internal forces at node C. (Indicate whether the forces are in compression or tension.) The internal forces in the elements CH, CD and HI. (Indicate if the forces are in compression (C) or tension (T)). Draw the respective free-body diagrams. Consider the following: A and F are supports. the angles a, B, y are angles of 90, 60 and 30 ° respectively (Check image pr2 for the image of the armor) (Check image pr2.2 for the values to be used)