A bar 0.25 m in length having square cross-sectional area is subjected to an axial compression of 60 KN. The axial strain induced is 0.0030. Young’s modulus of 95 GPa and Poisson’s ratio is 0.27. Compute the stress, lateral deformation and cross-sectional area required.

Q: Consider a point in a structural member that is subjected to plane stress. Normal ar vertical planes…

A:

Q: A steel plate is bent into a circular arc of radius 10 m. If the plate section be 120 mm wide and 20…

A: Given a steel plate bent into a circular arc with, E=2×105 Nmm2. Arc radius, R = 10 m. Area, A=120…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 95 MPa and Sy =…

A:

Q: indicated in the figure. Using the equilibrium equation approach, determine the normal and shear…

A: Given data in question  Stresses Angle To find out  Normal and shear stresses

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are Sy = 60 MPa and Sy =…

A:

Q: In a strained material stresses are given below sigma_x=100Mpa, sogma_y=-50Mpa, txy=30Mpa.calculate…

A: Solution:-

Q: The stresses shown act at a point in a stressed body.  The stress magnitudes are Sx = 75 MPa and Sy…

A: Given data in question  Normal stresses Angle To find out  Normal and shear stresses

Q: A thin rectangular plate having the dimensions of a -20 mm and b-12 mm is acted upon by a stress…

A: A rectangular plate given asThe resulting strain Need to findChange in length in diagonal AC and QB

Q: The stresses shown act at a point in a stressed body. Determine the normal and shear stresses at…

A:

Q: A solid circular torsional member OPQ is subjected to torsional moments as shown in the figure (not…

A: A solid circular torsional member OPQ,

Q: Question A structural element is subjected to a two dimensional stress system, wherein ₁ = 225 N/mm²…

A: Given- Stresses- σ1=225 N/mm2,σ2=compressive,Possion's ratio μ=0.25, It is needed to find the value…

Q: Show the type of stress distribution over the radius of the disk 3. How is the correspondence…

A: The area of the middle section of the rod is reduced with respect to both ends which means the disk…

Q: If the principal stresses in a plane stress problem, are 0₁ = 100 MPa, o₂ = 40 MPa, the magnitude of…

A: Given- Principal stresses- σ1=100 MPa,σ2=40 MPa, It is needed to find the magnitude of maximum shear…

Q: A steel shaft AB of length 1.5 m and diameter 25 mm () carries a distributed torque of intensity t =…

A:

Q: For the strain &¸ =&₂=0, Y=0.002828 (in x-y coordinate system) at a specific point in an isotropic…

A: Given:Required:Strain components in n-t cordinate system

Q: 19. Compute the stress when the temperature drops to -20°C. The cross- sectional area of the rod is…

A:

Q: ) For the given stress condition find: 1. Principal stresses and their orientation. 2. The stresses…

A:

Q: a shear stress T =4 MPa also acts on it. According to Von- mises failure criteria, Von- mises stress…

A:

Q: The stresses shown act at a point in a stressed body. The stress magnitudes ares, indicated in the…

A:

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are S, = 2000 psi, Sy =…

A:

Q: At a point in a stressed material, the major principal stress is 7.2 ksi compression and the minor…

A: It is required to determine the maximum shear stress. We know that, the maximum shear stress acts at…

Q: The state of plane stress in a plate of 100 mm thickness is given as 0xx = 100 N/mm2, Oyy = 200…

A:

Q: A W360 x 122 section is used as a column with an effective length of 10 m. Determine the maximum…

A: Thus question belongs to subject Design of rcc structure. In this question find out Maximum load…

Q: 11.4 (A/B). Compare the strain energies of two bars of the same material and length and carrying the…

A: Given:- The diameter of the bar 1 = 25 mm The diameter of the bar 2 for half-length = 20 mm and for…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are S, = 75 MPa and S, =…

A: Given data in question  Normal stress on element  Angle  To find out  Normal and shear stresses

Q: The simply supported composite beam below is made by bolting two wood boards (E = 1,900 ksi) to the…

A: Given data: Wood board, E=1900 ksi Steel plate, E=29,000 ksi   It is asked to determine, 1.…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

A:

Q: Q5/ A thin plate is subjected to plane stress conditions. The stresses acting on the plate are as…

A: Step 1:   Step 2: Step 3: Step 4:

Q: he stresses shown act at a point in a stressed body. Normal and shear stress magnitudes acting on…

A:

Q: use method of consistent deformation in analyzing the rigid frame shown 25 kN/m B p = 220 kn 6 m

A: Fig1 Fig 2

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are S, = 85 MPa and S, -…

A:

Q: 3. A thin hollow sphere of radius 75 mm and thickness 30 mm is subjected to an internal pressure of…

A:

Q: At a point in a stressed material, the major principal stress is 66 kPa compression and the minor…

A: Given:

Q: The state of plane-stress at a point is given by Ox = = 100 MPa and -200 MPa, = 100 MPa. The Txy Oy…

A:

Q: The following stress element represents the stress state at point A of the structure in the figure…

A: