A balcony is supported outside a building by steel cantilever. The balcony is a m wide (length of the cantilever beam) and the total load carried is y kN/m² of floor area. The cantilever cross- section is b x d and the floor thickness is c. Note that y kN/m² varies between 11 and 19 kN/m² (each group to select their own value) Figure 1 a) Design your section if d = a/10 b = 3d/10 c = d/4 b) Calculate the maximum permissible spacing I if the allowable stress is 12 MPa.

A balcony is supported outside a building by steel cantilever. The balcony is a m wide (length of the cantilever beam) and the total load carried is y kN/m² of floor area. The cantilever cross- section is b x d and the floor thickness is c. Note that y kN/m² varies between 11 and 19 kN/m² (each group to select their own value) Figure 1 a) Design your section if d = a/10 b = 3d/10 c = d/4 b) Calculate the maximum permissible spacing I if the allowable stress is 12 MPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 300mm x 500mm rectangular concrete beam is reinforced with four pieces 25mm diameter bars. The beam is simply supported on a span of unknown length. The uniform linear dead load from the slab is 18KN/m (weight of beam not included) and the uniform linear live load is 10kN/m. The effective depth of the beam is 430mm. the beam. Use area of one 25mm diameter bar = 510mm2. Using your own values of fc' = 20.1 MPa and fy = 335 MPa from the excel file, determine the safe length
2. Determine the resultant of the forces applied on a simply supported beam as shown. SKU SKN म im+im+im+ 2m HOKNI
Concrete T-beam has been reinforced by bonding a steel plate to its web asshown below. The beam carries a uniformly distributed load of 40kN/m over a simply supported 8m span. Find the maximum deflection of the beam on the assumption that the concrete is fully operative in both tension and compression.(Est = 200kN/mm^2. Econc = 30kN/mm^2; central deflection due uniformly distributed load, total W acting on a simply supported beam of span L= 5WL^3/(384EI)) can someone please answer this question in detail who is confident in this topic with step-by-step calculations & sketch pls. I've asked this question twice now and I've gotten different answers each time so I'm at a bit of a loss. (DONT respond to this if you have already responded previously) Thank you
Rectangular reinforced concrete beam section b = 40 cm, h = 60 cm, d = 53 cm, material strength fy = 4200 = 4200 kgf / cm^2, fc ' = 280 kgf/cm^2, beam section configuration #4 For closed stirrups @15 cm, the net cover is 4 cm, and the beam section is subjected to a torque of Tu = Tcr. Q: What is the ultimate shear load value Vu that the beam section can bear. Among them, Tcr is the cracking torque of the beam section, #4 steel bar (db=1.27 cm, Ab=1.267 cm^2).
2. A rectangular beam with b = 250 mm and d = 460 mm is reinforced for tension only with 3-25 mm bars. The beam is simply supported over a span of 6 m and carries a uniform dead load of 0. 680 KN/m including its own weight. Use fy=276.50 MPa and fc'=20.70 MPa. The value of omega "w" is. O 0.171 O 0.128 O 0.085 0.212 0.294 O 0.337
A simply supported wood beam is reinforced with a steel plate of width b as shown in the figure. The beam carries a uniformly distributed load including the weight of the beam) of intensity 273 lb/ft over its 18-ft span. Using b = 4 in. and Est/Ewd = 20, determine the maximum bending stress (in psi) in the steel. Round off the final answer to two decimal places. - 6 in. - 10 in. 1/2 in. -b-
the floor framing plan of a reinforced concrete building. All beams are 300 mm x 600 mm. The properties are as follows: slab thickness = 100 mm; super imposed dead load = 3 kPa; live load = 4.8 kPa; concrete unit weight = 24 kN/m3. The columns at E and H are deleted thus girder BEHK alone supports beam DEF at E and beam GHI at H. Calculate the uniformly distributed service dead load at beam DEF in kN/m Calculate the uniformly distributed service live load at beam DEF in kN/m.
please put in 3 decimal places thank you for the help
Really need please. New solution if possible.
1000 N/m Given: A cantilever beam has loading and cross section as shown. The allowable stress is 64 MPa. 150 mm Determine: the minimum width for the beam 6 m b
4
1. A typical cross-section of a roinforced concrete T-beam is shown in the figure below. The beam is reinforced with eight 25 mm diameter bars in tension zone. For the purpose of analysis, use the effoctive depth of 575 mm. Use f. = 25 MPa and f, = 420 MPa. Determine øM, 1000 mm T100 mm 8-D25 300 mm 575 mm ww G29