A balanced delta connected load having an impedance Z, = 300 + j210 ohms in each phase is supplied from a 400V 3-phase supply thru a 3-phase line having an impedance of Z_ = 4 + j8 in each phase. Determine a. total power supplied to the load b. current in each phase of the load

A balanced delta connected load having an impedance Z, = 300 + j210 ohms in each phase is supplied from a 400V 3-phase supply thru a 3-phase line having an impedance of Z_ = 4 + j8 in each phase. Determine a. total power supplied to the load b. current in each phase of the load

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.42P: A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase...

See similar textbooks

Related questions

Q: (a) Is this a Mealy machine or Moore machine? (b) Fill in the outputs on the transition table. (c)…

Q: Find I in the following circuit using nodal analysis. j42 6/30° V 4/20° V

Q: alternator is rated at 15kVA, 460V. The armature resistance and reactance are 1.50 and 30…

A: In this question we will find single phase alternator no load voltage with given data...

Q: Reduce the biock diagram. H. R. G, G. G H, Q2

Q: A 12-bit DAC has a full-scale output of 15.0V. Determine the resolution, the percent resolution, and…

Q: 9.) Assume the frequency to be 60 Hz. Calculate the inductance or capacitance in series for the…

Q: Find the current in a ground loop that is 250 m long, has a wire resistance of 0.04 ohms/m, and has…

Q: (b) If the 9-point sequence x[n] represents a time-domain signal sampled at 3 kHz, what frequency…

A: Time domain signal is represent the according to time ,signal is change . and frequency domain…

Q: Question a, Draw a sine wave with a frequency of 250 Hz that lasts for a duration of 12 ms and…

A: Given a sinusoidal signal of 5V. f=50 Hz

Q: You are given a report that shows 2 different designs of a quadruple stage impulse generator…

A: Design "A" is more suitable for creating impulsive voltage waveforms than Design "B."

Q: iii) The efficiency u of an AM signal is defined as the percentage of the total powe carried by the…

A: In this question we will find efficiency of AM wave for given modulation index and maximum…

Q: Determine the output impedance (Zo) for the given network with the following conditions: gfs =…

A: Impedance is calculated the opposite of current flow . it is represented by 'Z'. for direct current…

Q: 1-Compare between calculated, direct measured and Norton's equivalent (F)Discussion:- T-Compare…

Q: 9.) Assume the frequency to be 60 Hz. Calculate the inductance or capacitance in series for the…

Q: A 1Φ alternator is rated at 15kVA, 460V. The armature resistance and reactance are 1.5Ω and 3Ω…

Q: Everyone in the middle east about the situation for decades.

A: In the given question, we have to select the correct tense for the situation. Since the sentence is…

Q: Determine the current Io using mesh analysis UTM j2 n yoTM &UTM UTM 420° 80 UTM 25290° V 1520° A 25…

Q: Consider the following periodic signal: x(n) = [. 1 012 3 210 1 1 (A)Sketch the signal x(n) and its…

Q: E = K,ONvolts-where NIS Example 8.8. Afour-pole generator, having wa ve-wound armature winding has…

A: The solution is given below

Q: Give impacts of split phase induction motor on users

A: The induction motor of split phase type is a single-phase induction motor having a starting or the…

Q: For tha circnits ahown, calenlat phe curront hrough the 9 A reaiator a img za Enperposition theotem.…

A: According to superposition theorem, total output across the load is equal to the summation of…

Q: A transformer with a 240 primary voltage 01,440 V O 240 V O40 V 6 V

Q: A single core cable has a conductor diameter of 1 cm and insulation thickness of 0.4 cm. If the…

Q: i,(t) = 5 sin(2t+ 60°) Amperes I. What are the magnitude A, the angular frequency sinusoid? Express…

Q: Q3 Referring to the circuit in Figure Q3, determine the values of current, i, and iz by using nodal…

A: We need to find current for given circuit

Q: (TCO 1) If the gain in decibels of an amplifier is 76.9, what is the straight gain? 6998 6578 6745…

A: Gain in db=20log10(Gain in Linear)

Q: 20. If a 12-uf capacitor has a capacitive reactance of 54.2 ohms, the value of w is A. 1537.5. B.…

Q: 3.) A voltage v = 120 sin (275t + %3D Tt/2) is applied to a capacitor rated 68 µF. Find the r.m.s.…

A: To find the RMS value of current through capacitor

Q: : use she Thananins theore m to find thk cni'rent flow ing drough alu GA nasistar sia netwerk snown.…

Q: 14.) Find the value of power dissipated if a voltage v = 240 sin (30t + Tt/4) is applied to a…

A: Power dissipation in a resistor: The power dissipates in the resister in the form the heat and the…

Q: A wye-connected, 3-phase system has the following sequence components of current Zero sequence…

A: In this question, We need to determine the flow the current in the neutral wire? If all sequence…

Q: Given a switching function f(A, B,C, D) = A'BD + AC'D. a) Find its minterm and maxterm expansions.…

A: Given data FA,B,C,D=A,BD+AC,D

Q: Binary codes. Convert from Gray code to binary X1 = 10101111. From the result obtained, apply a…

A: The solution is given below

Q: Summarize the differences between passive filter and active filter in terms of gain, cost and…

A: You have asked multiple independent questions. We are authorized to answer one question at a time.…

Q: HOW YOUR COMPLETE SOLUTION SOLVE FOR vector A = (x2 – y2)ay + 48az in spherical coordinates at B (r…

A: Given Vector A=x2-y2ay+48 az Spherical Coordinates Br=14,θ=36°,ϕ=128°

Q: The analysis of the voltage, V for the cireuit given in Figure Q4 can be expressed in the following…

A: Id =0.5882 V3 =200×0.5882=117.64 V

Q: Tough cookie for one point! :-) L1 R 1H || 1kQ L2 600mH Not coupled coils 120VRMS 140 Hz What value…

Q: For the voltage-divider bias configuration. Determine the level of output impedance or Zo with the…

Q: Deter mine the node ages 502 P. Me 9. 2A (T +) iov 402 10

A: We need to find out node voltage for given circuit

Q: The balanced system below has a phase voltage of 120 V. It supplies a balanced load coil that is…

Q: For tha cirenits ahown, calenlab rhe currout hrongh the 9 A resiator as ing za emperposition…

Q: What time constant τ = CthRth is needed so that a 1 kW electrical system that is 90% efficient…

A: One time Constant is that time after which the output reaches 63% of its steady state value. Time…

Q: (c) The DFT matrix given in Figure Q2 (c) uses twiddle factors (Wk) to compute the 4-point DFT…

Q: Given the following x(n) h;(n) h,(n) h;(n) ► y(n) h1(n) = {2, 2, 1} %3D h2(n) = u(n) 2/2 sin (n)…

A: Given the following: h1(n)={2,2,1}h2(n)=12nu(n)h3(n)=223nsinπ4nu(n) 1. We need to determine the…

Q: Draw the equivalent circuit with 2A acting alone 0.21, 5kN + 1V 7k2 4k2 ) 2A

Q: Please write a long explanation so that we can report back to you Ideal Non-inverting Operational…

Q: The balanced system below has a phase voltage of 120 V. It supplies a balanced load Z1 that has…

A: In this question we need to find a total reactive power and true power of the given three phase…

Q: A current balance bridge shown in Fig. 2 has resistance of R1 = R2 = 1kQ, R4 = 5902, R5 = 102, and V…

A: To find the value of R3 if a current of 0.5 mA is required to Balance the bridge .

Q: Draw the Thevenin and Norton equivalent circuits and reconnect the load resistor R1. 2i, I 500Ω )…

A: We need to find out thevenin equivalent circuit across point a and b.

Q: 2) The amplitude of the emf in the below circuit is 150V, while the angular frequency is 60x. The…

Concept explainers

Single Phase AC Circuit

Alternating Current (AC) is a type of electric power in which the electric current changes, both in magnitude and direction, at regular intervals. This AC Circuits can deliver power in either a Single Phase system or a Three Phase system.

Question

A balanced delta connected load having an impedance Z, = 300 + j210 ohms in each phase is
supplied from a 400V 3-phase supply thru a 3-phase line having an impedance of Z_ = 4 + j8
in each phase. Determine
%3D
a. total power supplied to the load
b. current in each phase of the load

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis of Single Phase and Three Phase System

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider a three-phase Y-connected source feeding a balanced- load. The phasor sum of the line currents as well as the neutral current are always zero. (a) True (b) False
Two balanced Y-connected loads, one drawing 10 kW at 0.8 power factor lagging and the other IS kW at 0.9 power factor leading, are connected in parallel and supplied by a balanced three-phase Y-connected, 480-V source. (a) Determine the source current. (b) If the load neutrals are connected to the source neutral by a zero-ohm neutral wire through an ammeter, what will the ammeter read?
It is stated that (i) balanced three-phase circuits can be solved in per unit on a per-phase basis after converting - load impedances to equivalent Y impedances. (ii) Base values can be selected either on a per-phase basis or on a three-phase basis. (a) Both statements are true. (b) Neither is true. (c) Only one of the above is true.
Figure 3.32 shows the oneline diagram of a three-phase power system. By selecting a common base of 100 MVA and 22 kV on the generator side, draw an impedance diagram showing all impedances including the load impedance in per-unit. The data are given a follows: G:90MVA22kVx=0.18perunitT1:50MVA22/220kVx=0.10perunitT2:40MVA220/11kVx=0.06perunitT3:40MVA22/110kVx=0.064perunitT4:40MVA110/11kVx=0.08perunitM:66.5MVA10.45kVx=0.185perunit Lines I and 2 have series reactances of 48.4 and 65.43, respectively. At bus 4, the three-phase load absorbs 57 MVA at 10.45 kV and 0.6 power factor lagging.
Three single-phase transformers, each rated 10MVA,66.4/12.5kV,60Hz, with an equivalent series reactance of 0.1 per unit divided equally between primary and secondary, are connected in a three-phase bank. The high-voltage windings are V-connected and their terminals are directly connected to a 115-kV three-phase bus. The secondary terminals are all shorted together. Find the currents entering the high-voltage terminals and leaving the low-voltage terminals if the low-voltage windings are (a) Y-connected and (b) - connected.
The three-phase source line-to-neutral voltages are given by Ean=100,Ebh=10+240, and Ecn=10240volts. Is the source balanced? (a) Yes (b) No
A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase 60-Hz,208-V source, (a) Calculate the line current, the total real and reactive power absorbed by the load, the load power factor, and the apparent load power, (b) Sketch a phasor diagram showing the line currents, the line-to-line source voltages, and the -load currents. Use Vab as the reference.
Two delta connected loads are connected in parallel and powered by a balanced Y-connectedsource. The smaller of two loads draws 10 kVA at a lagging power factor of 0.75 and the largerdraws 25 kVA at a leading power factor of 0.8. The line voltage is 400 V. Calculate a) The powerfactor at which the source is operating. b) The total power drawn by the two loads. c) The phasecurrent of each load.
A three-phase system has balanced conditions so that the per-phase circuit representation can be used as shown in Figure 1 Select the turns ratio of the step-up and step-down transformers that the system operates with an efficiency greater than 99 percent. Moreover, find the complex power (received or given) of all components in the circuit and the V1 and V2 voltages. The load voltage is specified as 4 kV rms, and the load impedance is 4/3 ohm. ..
VA-120 V4120 Z₁ volt In lc c ZA Three-phase source Feeder lines Balanced load In the above circuit diagram, we have source impedance Zg = 0.05+j0.15 ohm, Z₁ = 0.1+j0.2 ohm and per phase impedance in the balanced Delta connected load, Z₁ = 12+j9 ohm. RMS value of source voltage is 200 volt. Phase sequence is as shown in the diagram. RMS value of current Ic= ampere Phase angle of le= degree RMS value of line voltage VCA = B JAB Inc ICA
1. The following are the given for the circuit below: VRY = 220 cis 0°, VYB = 220 cis -120° and VBR = 220 cis -240°. IR = 10 cis 0°. The load is balanced and delta connected. Determine the: (a) Impedance per phase (b) Current per phase (c) Line currents. B R reellle relllle momm Y RY Iy IB ĪR B R ZBR VYB ZRY
Draw a 3-phase wye-connected generator with transmission lines connected to a 3-phase delta-connected load. Assume the lines connecting them have an inductance of j5 per phase. The generated voltages are 120 Vrms with phase 'a' having a phase angle of 0°. The loads are 10 Ohm resistors per phase. When drawing, make sure to label all 3 phases with voltage phasors, line inductances, and load resistances.