a- Assume that the active component of the load on the circuit is 0.6 p.u. Find the initial power angle 8. b- With the value of the load set at 0.6 p.u., a three-phase short circuit takes place in the middle of transmission line 1. Will the system be stable under a sustained fault? c- Assume that the active component of the load on the circuit is 0.3 p.u. Find the initial power angle 6. d- With the value of the load set at 0.3 p.u., a three-phase short circuit takes place in the middle of transmission line 1. Will the system be stable under a sustained fault?

a- Assume that the active component of the load on the circuit is 0.6 p.u. Find the initial power angle 8. b- With the value of the load set at 0.6 p.u., a three-phase short circuit takes place in the middle of transmission line 1. Will the system be stable under a sustained fault? c- Assume that the active component of the load on the circuit is 0.3 p.u. Find the initial power angle 6. d- With the value of the load set at 0.3 p.u., a three-phase short circuit takes place in the middle of transmission line 1. Will the system be stable under a sustained fault?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

4.In a double line-to-ground fault we can expect thatImmersive reader A) There are currents in the ground connections. B) The current values in the ground connections are zero. C) Short-circuit currents exist in all three phases. D) The currents in the faulted phases are equal. E) N. A.
X 0.1j Z12 = 0.1 j Z23 = 0.1 j 0.2 j KAY 02) 0.1j Load 1 Load 2 Load 3 Consider the single line diagram shown in the figure. All impedances are expressed in per unit on a common 100 MVA base. The generator transient reactance =0.5 j. The Bus 1 prefault voltage (1 + 0.0 j). If a bolted three phase fault occur at bus 1. The magnitude of fault current is: Select one O a. 5.8 pu b. 7.5 pu c. less than 5.8 pu O d. 11.6667 pu e. greater than 12.0 pu
A 4-bus three-phase power system consists of the following equipment: • Generator 1 connected to bus 1 with a rated power of 20MVA, rated voltage of 20 kV, and a series reactance of 0.4 p.u. • Generator 2 connected to bus 5, with a rated power of 12MVA, rated voltage of 10 kV, and a series reactance of 0.3 p.u. Transformer 1 connected between buses 1 and 2, is wye-wye connected with a rated power of 20 MVA, rated voltages 20/100 kV, and a series reactance of 0.1 p.u. • Transformer 2 connected between buses 4 and 5, is wye-wye connected with a rated power of 12 MVA, rated voltages 12/110 kV, and a series reactance of 0.15 p.u. • Transmission Line 2-3 connects buses 2 and 3 and had a series impedance of 50 + j75 ohms. • Transmission Line 3-4 connects buses 3 and 4 and had a series impedance of 40 + j80 ohms. • Load A connected to bus 3 and abosorbes20 MW and 10 MVAR. The voltage at bus 3 is 105 kV. 1) Draw the one-line diagram for the system. 2) Draw the per-unit, per phase…
The fault current level of a circuit breaker used in a transmission line with phase voltage 4.6 kV and breaking capacity 50 MVA is . . kA.
(Q.2) For the following network, calculate the fault currents (IF1, IF2, IF3 and IF.) in pu and in kA, and fault MVA (ie. short-circuit level) at the indicated locations. Internal reactance of generators are j0.9 pu. Base quantities: 11 kV, 400 MVA on the generator side. 113.3 kV 4 MVA, 7% j0.5 2 j0.4 2 300 A 200 A 11 KV 250 MVA
A hydro powered 50 MVA generator, with a synchronous reactance 0.33 p.u., delivers 40 MW over a transmission line of 0.15 p.u. reactance to an infinite system. A 3-phase short circuit transient fault occurs on the busbar between the generator and transmission line. Given that the generator emf is 1.4 p.u. prior to and during the fault and all reactances are to a 50 MVA base: Sketch the single line schematic diagram of the system. Determine the maximum load angle the generator can swing to without losing stability. i) ii) iii) iv) Sketch the corresponding power-angle curve for the system showing the accelerating and decelerating areas. Calculate the critical clearing angle of the system to keep its stability.
Consider the system shown in the single-line diagram of Figure (3). All reactances are shown in per unit to the same base. Assume that the voltage at both sources is 1 p.u. a Find the fault current due to a bolted- three-phase short circuit at bus 3 b- Find the fault current supplied by each generator and the voltage at each of the buses 1 and 2 under fault conditions 0.06 p.u. 0.2 p.u. 0.04 p.u. 0.25 p.u. 0.2 p.u. 0.2 p.. 0.2 p.u. 0.06 p.u. 0.25 p.u. Figure (3) Single-line diagram ele ver ele 888 ele 0.06 p.u. 0.25 p.u.
If the source impedance at a 13.2 kV distribution substation bus is (0:5 + 1:5) Q per phase, compute the RMS and maximum peak instantaneous value of the fault current, for a balanced three-phase fault. For the system (X/R) ratio of 3.0, the asymmetrical factor is 1.9495 and the time of peak is 7.1 ms (see Problem 1). Comment on the withstanding peak current capability to which all substation electrical equipment need to be designed. Problem 1 Consider the expression for i(f) given by i(t) = v21ms [sin(@t-0-)+ sin 0,.eR/X)] where ez = tan-1 (WL/R). (a) For (X/R) equal to zero and infinity, plot i(f) as a function of (wf). (b) Comment on the DC offset of the fault current waveforms. (c) Find the asymmetrical current factor and the time of peak, tp, in milliseconds, for (X/R) ratios of zero and infinity.
The system values are given below. The bus 1 voltage after fault = 1.5 p.u The bus 2 voltage after fault = 1.2 p.u The line admittance between bus 1 and bus 2 (Y12 ) is = 0.8 p.u The post fault current current flow between bus 1 and 2 is ..............
Contribution of fault analysis in power system netwrok?
Q. 13. Transmission systems that produce switching surges higher than lighting surges are the ones that operate at: A. 200 kV B. 300 kV C. 400 kV D. B and C Q. 14. When constructing volt time curve, if flashover occurs on the tail side of the wave, the point on the curve will have a voltage magnitude equal to: Whos A. The applied wave peak B. The applied wave flashover point C. The applied wave peak multiplied by a factor of 0.9 D. The applied wave flashover point multiplied by a factor of 0.9
In a short circuit test on a 120 kV, 3 phase system, the breaker gave the following results: p.f. of fault 0.6, recovery voltage 0.9 times full line voltage, breaker current symmetrical, and restriking transient had a natural frequency 12 kHz. Determine average RRRV. Assume fault is grounded.