(a) A steel cantilever beam with a 1-in-diameter round cross section and length of 10 in is loaded at the tip with a transverse force of 1000 lbf and an axial force of 5000 lbf, as shown in the figure. Study the significance of the transverse shear stress in combination with tension and bending by calculating magnitudes of the stresses. Explain and comment on the stresses and strains generated. 1000 Ibf it. B 1 in dia. Cross section at the wall 5000 Ibf

(a) A steel cantilever beam with a 1-in-diameter round cross section and length of 10 in is loaded at the tip with a transverse force of 1000 lbf and an axial force of 5000 lbf, as shown in the figure. Study the significance of the transverse shear stress in combination with tension and bending by calculating magnitudes of the stresses. Explain and comment on the stresses and strains generated. 1000 Ibf it. B 1 in dia. Cross section at the wall 5000 Ibf

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.25P: A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just...

See similar textbooks

Similar questions

A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
A rod of square 30x 30mm^2 cross-section subject to a compressive axial force of 72kN and a twisting moment of 168.5N.m. Calculate the principal stresses and the maximum shear stress atthemostcritical point in the rod.
A rod of square 30x 30mm2cross-sectionsubject to a compressive axial force of 72kN and a twisting moment of 168.5N.m. Calculate the principal stresses and the maximum shear stress atthemostcritical point in the rod.
A 3-in. by 6-in. steel (E-29,000 ksi) bar (4-foot long) is subjected to the loads shown. Calculate the combined stresses at points A and B (be sure to indicate either tension or compression). Remember, the bar is bending in the strong direction so calculate your I accordingly. 1(1/12) (B)"(H) S=l/c A B. 6" 10,000 lbs 45,000 Ibs
A member is subjected to a major stress of 110 MPa (tensile), minor stress of 40 MPa (compressive) along with a counter clockwise shear stress of 23 MPa. Calculate the Normal stress, tangential stress, Resultant stress and its inclination on plane make 35° to major stress. Validate your analytical results by drawing Mohr's circle. (i) Normal Stress (unit is MPa) = (ii) Tangential Stress (unit is MPa) = (iii) Resultant Stress (unit is MPa) = (iv) Resultant inclination (unit in degree)
3 A bar of diameter 25mm has an axial hole 19mm bored out concentric with the outer circumference. The bar is submitted to the following loads simultaneously: (a) An axial tension of 13 kN, (b) A bending moment of 100Nm. Determine the maximum and minimum direct stresses on the section of the bar.
In an experimental determination of principal stresses a cantilever of hollow circular cross section is subjected to a varying bending moment and torque; the internal and external diameters of the cantilever are 40 and 50 mm, respectively. For a given loading condition the bending moment and torque at a particular section of the cantilever are 100 and 50 Nm, respectively. Calculate the maximum and minimum principal stresses ata point on the outer surface of the cantilever at this section where the direct stress produced by the bending moment is tensile. Determine also the maximum shear stress at the point and the inclination of the principal stresses to the axis of the cantilever. The experimental values of principal stress are estimated from readings obtained from a 45° strain gauge rosette aligned so that one of its three arms is parallel to and another perpendicular to the axis of the cantilever. For the loading condition of zero torque and varying bending moment, comment on the…
A 6-inch diameter pulley mounted on a 2-inch shaft as shown transmits 9 kW at 1000 rpm. What is the combined stress acting on the shaft?
A cast iron beam is of T-section as shown in Fig. The beam is simply supported on a span of 6 m. The beam carries a uniformly distributed load of 2 kN/m length on the entire span. Determine the maximum tensile and maximum compressive stresses.
A 180 mm diameter ship’s shaft rotates as 450 rpm and transmits 5 MW of power. The propeller causes an axial compression in the shaft of 1750 kN. Sketch the stress element on the shaft showing the three possible stress states. Hence, calculate for the position of maximum stress: 4.1 Principal stress on the shaft. 4.2 Maximum shear stress on the shaft. 4.3 The angle of maximum shear stress relative to the XY plane.
10.5 (B) A compound tube of 300 mm external and 100 mm internal diameter is formed by shrinking one cylinder on to another, the common diameter being 200 mm. If the maximum hoop tensile stress induced in the outer cylinder is 90 MN/m² find the hoop stresses at the inner and outer diameters of both cylinders and show by means of a sketch how these stresses vary with the radius. [90, 55.35,-924, 57.8 MN/m²]
1 %YY . 1:1. 1 docs.google.com Q بريدك الإلكتروني A vertical shaft is supported by a 5 نقاط thrust collar and bearing plate, as shown in Figure. Calculate the maximum axial stress of the shaft if the average punching shear stress in the collar and the average bearing stress between the collar and the plate are limited to 100 and 125 MPa, .respectively F100 mm- 150 mm Collar 25 mm إضافة ملف یالا - غرف الدردشة المجانية )aD( الصوتية المجانية: الدردشة الحية مع أصدقائك II