A: A single core cable covered by the lead, if the radius of the conductor is r and the insulator consists of three layers, draw the cross section of this underground cable and show where will be the maximum and minimum electric stress and how many electric stresses which can be accounted for this cable?

A: A single core cable covered by the lead, if the radius of the conductor is r and the insulator consists of three layers, draw the cross section of this underground cable and show where will be the maximum and minimum electric stress and how many electric stresses which can be accounted for this cable?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.17P: Determine the GMR of each of the unconventional stranded conductors shown in Figure 4.30. All...

See similar textbooks

Similar questions

If the cross sectional area of a conductor is doubled, then the resistance of the conductor remains the same. becomes half of the initial value. becomes double the initial value. becomes four times the initial value.
What do the conductors have in common? What do the insulators have in common?
Question 1 A ferromagnetic core is shown in Figure 1. The depth of the core is 5 cm. The other dimensions of the core are as shown in the figure. a) Find the value of the current that will produce a flux of 0.005 Wb. b) With this current, what is the flux density at the top of the core? c) What is the flux density at the right side of the core? Assume that the relative permeability of the core is 1000. cm -10 cm-- 20 cm 15 cm 500 turns 15 cm 15 cm Core depth 5 cm Figure 1
Question 1 A ferromagnetic core with a relative permeability of 1500 is shown in Figure 2. The dimensions are as shown in the diagram, and the depth of the core is 7 cm. The air gaps on the left and right sides of the core are 0.070 and 0.020 cm, respectively. Because of fringing effects, the effective area of the air gaps is 5 percent larger than their physical size. If there are 400 turns in the coil wrapped around the center leg of the core and if the current in the coil is 1.0 A, what is a) the flux in each of the left, center, and right legs of the core? b) the flux density in each air gap? 7 cm ст ст 30 cm 30 cm 7 cm 400 turns 0.05 cm 30 cm 0.07 cm 7 cm Core depth = 7 cm Figure 2
Question 1 Select all that apply. Which of the following are considered to be "core losses"? 12R heating loss Flux lines that bulge out at core gaps Currents that circulate within the machine non-ferrous components Field Lines that circulate around conductors and coils Rapid Changes in Domain orientation
Figure Q1(a) shows a piece of ferromagnetic core with magnetic flux (B) with circular current (I) around the core. Figure Q1(b) show laminated ferromagnetic core with the same magnetic flux (B) and circular currents. With the aid of diagrams, explain how the current as highlighted in red (I) is developed in the ferromagnetic core in Figure Q1(a). B (a) (b) Figure 1(a) A ferromagnetic core and (b) laminated ferromagnetic core
QUESTION 2 a) The total AAC cross sectional area is 544.7522 x 106 m2. Each strands having a radius of 0.34 cm and length of conductor is 2 m. Assume that the increase in resistance due to spiraling is 1.4 %. Given the resistivity of AAC at 20 °C is 2.83 x 10* Qm and T = 228 °C. Determine the total composed strands and DC resistance at 30 °C. b) Figure 2 shows the configuration of a single-phase two-conductor in the transmission line. Calculate the total inductance "Ltotal" of the line. (Given, rx = 0.02 m and ry-0.03 m) 3' 1.20 m 0.22 m 2.09 m 0.44 m 2" Conductor 'x' Conductor 'y' Figure 2
Two conductors, one of copper and the other of iron, are connected in parallel and carry equalcurrents at 25°C. How many percent of the total current will the copper conductor carry if thetemperature is raised to 100°C? The temperature coefficients of resistance at 0 °C are 0.0043 /°Cand 0.0063 /°C for copper and iron, respectively.
True or False: If the core material has a high reluctance, flux will flow freely in a magnetic circuit with a conductor with a high applied voltage.
I changed the wire material from copper to aluminum to string refer to the figures below. Can you explain the difference of the three materials? There are overload that happened.
Q1. Figure 1 shows the magnetic circuit with cross section area of core, 1000 mm2 and current source, 10 mA. By assuming the absolute permeability of core is 2.513x103 H/m, analyze the circuit and determine the following parameters: a. Draw the equivalent Ampere Circuital Law model b. Total reluctance of magnetic circuit c. Magnetic flux at centre and both sided d. Magnetic flux density at centre and air gaps e. Magnetic flux strength at centre and air gaps f. Briefly explain, effect to the magnetic circuit if the length of air gaps keep decreasing and increasing. at 7 cm 30 cm 30 cm 7 cm 7 cm 30 cm 1 cm 400 turns 1 cm 7 cm Figure 1 B-H CURVE BIT) 16 Sheet steel Cast steel 14 12 1.0 08 Cast iron 0.6 04 0.2 H(AUm) 500 1000 1500 2000 2500 3000 3500 4000 4500 5000
Describe what will happen to the current flow through a conductor given the following changes in properties: a) Increase in electrical resistivity -b) Decrease in electrical conductivity -c) Increase of temperature -d) Decrease in length -e) Thinning -